001: Demo mode
002: http://www.ifix.net.cn/thread-2550-1-3.html
003: The currently selected:W25Q256FV(ISP), capacity: 256Mbits, 32Mbytes.
004: Programmer is connected error.
005: http://www.ifix.net.cn/thread-2550-1-3.html
006: The currently selected:W25Q256FV(ISP), capacity: 256Mbits, 32Mbytes.
007: Serial number:2481, Programmer firmware version: V1.0 .
008: >------------------------------------OK---------------------------------------<
009: Ignore the chip ID to continue.
010: Start reading chip......
011: Status register 1 values: 0xFC, Status register2 values: 0xFF .
012: Buffer data checksum: 16bits_0x8F36 32bits_0xF25C8F36 :
013: Elapsed time: 51.2 seconds-average speed of 1310668 bytes/sec.
014: >------------------------------------OK---------------------------------------<
015: File has been saved.
016: Ignore the chip ID to continue.
017: Start erasing chip, please be patient..
018: This type of chip capacity is big, so erase time is take longer, please be patient!
019: Erase successful-Elapsed time 4.725 seconds
020: Auto blank checking...
021: Chip is not blank, start position: 0x0.
022: Blank check failure-Elapsed time-0.111 seconds
023: Erase error!
024: X\DH_XVR5X08_ENG_P_V3.BIN
025: X\DH_XVR5X08_ENG_P_V3.BIN
026: File has been loaded, checksum: 16bits_0x8FA9 -32bits_0x8F1B8FA9 :
027: Ignore the chip ID to continue.
028: Start writing chip..
029: Auto erasing..
030: This type of chip capacity is big, so erase time is take longer, please be patient!
031: Erase successful-Elapsed time-4.931 seconds
032: Start writing...
033: Write error, operation terminated.
034: X\W25Q256FV(ISP)_20200923_151624.BIN
035: X\W25Q256FV(ISP)_20200923_151624.BIN
036: File has been loaded, checksum: 16bits_0x8F36 -32bits_0xF25C8F36 :
037: Load the attached file in the status register1 values: 0xFC.Status register2 values: 0xFF.
038: X\W25Q256FV(ISP)_20200923_151624.BIN_STATUSREGVAL
039: X\W25Q256FV(ISP)_20200923_151624.BIN_STATUSREGVAL
040: File has been loaded, checksum: 16bits_0xFFFD -32bits_0xFDFFFFFD :
041: Ignore the chip ID to continue.
042: Start writing chip..
043: Auto erasing...
044: This type of chip capacity is big, so erase time is take longer, please be patient!
045: Erase successful-Elapsed time-4.991 seconds
046: Start writing...
047: Write error, operation terminated.

F50L1G41A-2Y(ECC_DIS)@LGA8C
F50L1G41A-2Y(ECC_EN)@LGA8C
(ESMT)
001: Serial number:2xx1, Programmer firmware version: V1.0 .
002: http://www.ifix.net.cn/thread-2550-1-3.html
003: The currently selected:F50L1G41A-2Y(ECC_DIS)@LGA8C, capacity: 1056Mbits, 132Mbytes.
004: >------------------------------------OK---------------------------------------<
005: Chip pin3,7Chip pins is detected poor contact.
006: Chip pin3,7Chip pins is detected poor contact.
007: Chip pin3,7Chip pins is detected poor contact.
008: Chip ID verification OK.
009: Start erasing chip, please be patient......
010: Erase successful_Elapsed time_9.231 seconds
011: Auto blank checking...
012: ECC Disable
013: Blank check successful_Elapsed time_460.5 seconds
014: Erase successful_Elapsed time_469.8 seconds
015: >------------------------------------OK---------------------------------------<
016: HS-X\С X08_ENG_P_V3.270307.BIN
017: HS-X\С X08_ENG_P_V3.270307.BIN
018: File has been loaded, checksum: 16bits_0x8FA9 _32bits_0xC8DB8FA9 :
019: Chip pin3,7Chip pins is detected poor contact.
020: Chip pin3,7Chip pins is detected poor contact.
021: Chip pin3,7Chip pins is detected poor contact.
022: Chip ID verification OK.
023: Start writing chip......
024: ECC Disable
025: Auto erasing...
026: Erase successful_Elapsed time_9.27 seconds
027: Start writing...
028: Write successful_Elapsed time_54.25 seconds
029: Auto verifying...
030: ECC Disable
031: All bytes verification are consistent in good blocks.
032: Elapsed time: 109.2 seconds_average speed of 1267439 bytes/sec.
033: >------------------------------------OK---------------------------------------<