Добрый день. Coolfort CF-3201 Плата YBS-350_MAIN_V05 SOC R16-J, Micom GD32F103VCT6 NAND MX30LF2G18AC Аппарат реагирует на кнопку включения, начинают медленно мигать белые светодиоды, звуков нет, Wifi не поднимается, уборку не начинает. Судя по логу, после Starting kernel, через пару минут перезапускается и так постоянно. Ищу дамп NAND. Лог загрузки во вложении.
Код
HELLO! BOOT0 is starting! boot0 version : 4.2.0 boot0 commit : a1ae6c20d88d561753072492191f817d9ff10a36
fel_flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 DRAM DRIVE INFO: V1.7 DRAM Type =3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM zq value: 00003bbbDRAM CLK =552 MHZ ID CHECK VERSION: V0.1 using ic R16 USE PLL DDR1 USE PLL NORMAL PLL FREQUENCE = 1104 MHZ DRAM PLL DDR1 frequency extend open ! DRAM master priority setting ok. Auto calculate timing parameter! para_dram_tpr0 = 0047214f para_dram_tpr1 = 01c2294b para_dram_tpr2 = 00061043 tcl = 6,tcwl = 4 DRAM TIMING PARA0 = 0b0e180b DRAM TIMING PARA1 = 0003040f DRAM TIMING PARA2 = 0406050a DRAM TIMING PARA3 = 0000400c DRAM TIMING PARA4 = 05020405 DRAM TIMING PARA5 = 05050403 DRAM TIMING PARA8 = 90003310 DRAM PHY INTERFACE PARA = 02040102 DRAM VTC is disable DRAM dynamic DQS/DQ ODT is on DRAM DQS gate is PD mode. DRAM one rank training is on,the value is 91003587 DRAM work mode register value = 004318e4 DRAM SIZE =512 M set one rank ODTMAP DRAM simple test OK. dram size =512 NAND_ClkRequest, nand_index: 0x00001000 Reg 0x01c20080: 0x00053de3 Reg 0x01c20060: 0x00053dd6 Reg 0x01c202c0: 0x00053dd6 NAND_SetClk, nand_index: 0x0000000a Reg 0x01c20080: 0x00053de7 NB0 : nand phy init ok block from 4 to 39 nand block 4 is bad nand block 5 is bad nand block 6 is bad nand block 7 is bad current block is 8 and last block is 39. current block is 9 and last block is 39. current block is 10 and last block is 39. current block is 11 and last block is 39. current block is 12 and last block is 39. current block is 13 and last block is 39. current block is 14 and last block is 39. sum=4828c2fd src_sum=4828c2fd The file stored in start block %u is perfect. Ready to disable icache. Jump to secend Boot. [ 0.448]
[ 0.466]pmbus: normal or secure os ready [ 0.470]PMU: AXP221 [ 0.473]PMU: AXP22x found bat_vol=0, ratio=100 [ 0.478]PMU: dcdc3 1100 [ 0.481]PMU: pll1 1008 Mhz,PLL6=600 Mhz AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz dcdc1_vol = 3000 dcdc2_vol = 1100 dcdc3_vol = 1100 dcdc4_vol = 0 dcdc5_vol = 1500 aldo2_vol = 2500 aldo3_vol = 3000 find power_sply to end vbus not exist fel key new mode run key detect no key found no key input dram_para_set start dram_para_set end [ 1.605]DRAM: 512 MiB relocation Offset is: 1e1f3000 save config for small mem_size workmode = 0 [ 1.673]NAND: NAND_UbootInit NAND_UbootInit start NB1 : enter NAND_LogicInit uboot:nand version: 3 5003 20170418 1437 nand : get id_number_ctl fail, 1 uboot:nand info: 9590dac2 ffffff06 28c 0 0 nand : get sorting_flag fail, a nand : get CapacityLevel fail, 5eb96e90 not burn nand partition table! NB1 : nftl num: 1 init nftl: 0 NB1 : NAND_LogicInit ok, result = 0x0 [ 2.267]sunxi flash init ok In: serial Out: serial Err: serial --------fastboot partitions-------- -total partitions:9- -name- -start- -size- boot-res : 1000000 100000 env : 1100000 100000 boot : 1200000 400000 rootfs : 1600000 3000000 rootfs_data : 4600000 a00000 private : 5000000 100000 recovery : 5100000 2000000 misc : 7100000 100000 UDISK : 7200000 0 ----------------------------------- base bootcmd=run setargs_nand boot_normal bootcmd set setargs_nand key 0 cant find rcvy value cant find fstbt value misc partition found to be run cmd=run setargs_nand boot_normal sunxi_serial: sn_filename is not exist serial is: 28f7900c50c9ffffc386 Net: usb_etherWarning: failed to set MAC address
WORK_MODE_BOOT board_status_probe sunxi_bmp_logo_display out of usb burn from boot: without usb [ 2.396]Hit any key to stop autoboot: 0 fatload partition name: boot -> 2 ## Booting kernel from Legacy Image at 43800000 ... Image Name: ARM OpenWrt Linux-3.4.39 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3339696 Bytes = 3.2 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK [ 2.676][mmc]: MMC Device 2 not found [ 2.680][mmc]: mmc not find,so not exit NAND_UbootExit NB1 : NAND_LogicExit nand release dma:0 reload config to 0x43000000 [ 2.684] Starting kernel ...
Файлы
Прошивки
Продажа
Литература
Статьи
Зарегистрировано всего