Автор темы
Участники
|
Main Board: TPD.RT2841.PB772
CPU: RTD2841SAA
eMMC H26M41204HPR
Матрица V400HJ6-PE1 Rev c 3
Корыто LVF395NDEL
Здравствуйте уважаемые инженеры! Прошу помощи в поиске дампа eMMC для данного ТВ. После замены eMMC идет постоянная загрузка с флешки
▒$R:0000003D
Hello world, 284x!{uni}[WEI]
****System Start****
****RT2841_GMC****
svn:36b262711bb28b91 (Dec 14 2018 18:34:00)
flash_type = 2, secure_type = 2
b8062204=100
SKIP MMC PHASE SCAN
0xb8060520=0
0xb8060524=0
[go kb]KRRRRURRRU"U#U$:Y: boot current backlight is on ! [1]
rtk_hw_get_divider M_best:3 N_best:4095 freq:3 totalcnt:255 duty_max:255
set pwm duty=128 success!!
uboot_size=0x000c8210
kboot_size=0x00070110
after 512bytes alignment, uboot_size=0x000c8400
after 512bytes alignment, kboot_size=0x00070200
emcu start id=0
[SUCCESS] backup_emcu:write emcu_1 success!
kboot start id=0
[SUCCESS] backup_kboot:write kboot_1 success!
uboot start id=0
[SUCCESS] backup_uboot:write uboot_1 success!
get header done
decrypt header size 16...
#############################
# Dump Rescue header:
# magic = 0x6331beef
# size = 0x00ae4424 (include header)
#############################
#############################
# Enter Rescue Linux:
# secure_mode = 2
# compressed = 1
# block_no = 0x00008000
# size_bytes = 0x00ae4424
# target_addr = 0x00108000
#############################
read done
to decrypt...
======================================================
the first 32-byte decrypted data(base=0x0c000000)
000 : ef be 31 63 24 44 ae 00 00 00 00 00 00 00 00 00
010 : 5d 00 00 80 00 38 90 f9 00 00 00 00 00 00 58 13
decrypt rescue successful
sw sha256 ret 0
start decompress rescue ...
:Y: boot current backlight is on ! [1]
Start Linux at 0x108000 ...
[muye]tmp_cmd=androidboot.console=ttyS0 console=ttyS0,115200 bufsize=80000
******* commdline androidboot.console=ttyS0 console=ttyS0,115200 bufsize=80000 envp=e4100 androidboot.verifiedbootstate=green androidboot.selinux=permissive ** *****
Kernel command line: androidboot.console=ttyS0 console=ttyS0,115200 bufsize=8000 0 envp=e4100 androidboot.verifiedbootstate=green androidboot.selinux=permissive flashtype=emmc mmcparts=rtkemmc:4632555k,1024k(/frp),8192k(/misc),16384k(/res), 32768k(/optee_armtz),8192k(/impdata),32768k(/cache),24576k(/userdata),8192k(/per sist),16384k(/rtdata),32768k(/tclconfig),1363152k(/vendor),1258292k(/system),463 2555k(/data) root=/dev/mmcblk0p1 rootfstype=ext4 ro rootwait bootcode_git_versio n=dependency_LOGBUF_20170314_170705-795-g6ee8f7b8 no_console_suspend loglevel=4 earlyprintk androidboot.serialno=0A302F34543439503788 ac_on chip=RTD284XA0 irda= 8-rca dvs_pin=0 dvs_iso_gpio=0
Core 1 stoped
Core 2 stoped
Core 3 stoped
Starting kernel ...
Reset ethernet/disable interrupt/flush cache...
bootargs=androidboot.console=ttyS0 console=ttyS0,115200 bufsize=80000 envp=e410 0 androidboot.verifiedbootstate=green androidboot.selinux=permissive flashtype=e mmc mmcparts=rtkemmc:4632555k,1024k(/frp),8192k(/misc),16384k(/res),32768k(/opte e_armtz),8192k(/impdata),32768k(/cache),24576k(/userdata),8192k(/persist),16384k (/rtdata),32768k(/tclconfig),1363152k(/vendor),1258292k(/system),4632555k(/data) root=/dev/mmcblk0p1 rootfstype=ext4 ro rootwait bootcode_git_version=dependency _LOGBUF_20170314_170705-795-g6ee8f7b8 no_console_suspend loglevel=4 earlyprintk androidboot.serialno=0A302F34543439503788 ac_on chip=RTD284XA0 irda=8-rca dvs_pi n=0 dvs_iso_gpio=0
RRRboot_jump_linux 0x00108000(0x0,0x648f5df4,0xe0100)
[ 0.000000] 00:00:00.000 (0)-0000 Wrong platform ? RTD284XA0
[ 0.000000] 00:00:00.000 (0)-0000 dvfs_pin:0
[ 0.819244] 00:00:00.815 (0)-0001 mtdoops: mtd device (mtddev=name/number) must be supplied
[ 0.910911] 00:00:00.907 (0)-0001 [KEYPAD] rtk_keypad_init(404)
[ 0.918027] 00:00:00.914 (0)-0001 Waiting for root device /dev/mmcblk0p1.. .
[ 2.392677] 00:00:02.389 (1)-0001 init: /init.rtk.rc: 28: invalid command 'setir_mouse'
[ 2.400943] 00:00:02.397 (1)-0001 init: /init.rtk.rc: 30: invalid command 'setir_mouse'
[ 2.501529] 00:00:02.497 (1)-0001 init: /dev/hw_random not found
[ 2.523371] 00:00:02.519 (1)-0001 init: /dev/hw_random not found
/ # [main:3766]: Starting LoaderM......
argc = 2
argv = /sbin/factory load
0+1 records in
0+1 records out
312 bytes (312B) copied, 0.000166 seconds, 1.8MB/s
command:/bin/busybox dd if=/sys/realtek_boards/system_parameters of=/tmp/str.txt , (line=207) [file=src/rtk_common.cpp], ret(0)
command:/bin/busybox mkdir -p /tmp/factory, (line=322) [file=src/rtk_factory.cpp ], ret(0)
[INSTALL INFO][src/rtk_factory.cpp][325] gfactory_start = 5400000
[INSTALL INFO][src/rtk_factory.cpp][326] gfactory_block_size = 400000
[INSTALL INFO][src/rtk_factory.cpp][327] gfactory_size = 400000
[INSTALL INFO][src/rtk_factory.cpp][328] gerasesize = 200
[INSTALL INFO][src/rtk_factory.cpp][196] pp_ok = 3 current_pp = 1 seq_num = 6971 tarsize =2088960
4080+0 records in
4080+0 records out
2088960 bytes (2.0MB) copied, 0.073615 seconds, 27.1MB/s
tar: short read
command:/bin/busybox dd if=/dev/block/mmcblk0 bs=512 count=4080 skip=180224 | /b in/busybox tar xp -C /, (line=481) [file=src/rtk_factory.cpp], ret(0)
command:/bin/busybox chmod 777 /tmp/factory/layout.txt, (line=521) [file=src/rtk _factory.cpp], ret(0)
command:/bin/busybox chmod 777 /tmp/factory/layout.txt_md5, (line=523) [file=src /rtk_factory.cpp], ret(0)
command:/bin/busybox chmod 777 /tmp/str.txt, (line=525) [file=src/rtk_factory.cp p], ret(0)
command:/bin/busybox chmod 777 /tmp/factory/env.txt, (line=527) [file=src/rtk_fa ctory.cpp], ret(0)
[INSTALL INFO][src/rtk_common.cpp][403] remove factory lock success
skipping malformed layout.txt line: #define CREATE_DATE " Jun 28 2019 "
skipping malformed layout.txt line: #define CREATE_TIME " 14:25:20 "
skipping malformed layout.txt line: #define BOOTTYPE " BOOTTYPE_UNKNOWN_BOOTTYPE "
skipping malformed layout.txt line: #define SSUWORKPART 0
alive!
skipping malformed layout.txt line: #define BOOTPART 0
skipping malformed layout.txt line: #define FW_KERNEL " target=deaddead offset=6 008000 size=1a5d100 type=aes "
skipping malformed layout.txt line: #define FW_AKERNEL " target=deaddead offset= 8c00000 size=33a620 type=aes "
skipping malformed layout.txt line: #define FW_VKERNEL " target=deaddead offset= 9100000 size=367020 type=aes "
skipping malformed layout.txt line: #define FW_KCPU " target=deaddead offset=970 0000 size=91778 type=aes "
skipping malformed layout.txt line: #define FW_DVLOGO " target=deaddead offset=a 300000 size=2a3000 type=raw "
(device:/dev/block/mmcblk0p1, mount_point:/frp, fs:ext4, size:1048576)
(device:/dev/block/mmcblk0p2, mount_point:/misc, fs:ext4, size:8388608)
(device:/dev/block/mmcblk0p3, mount_point:/res, fs:ext4, size:16777216)
(device:/dev/block/mmcblk0p4, mount_point:/optee_armtz, fs:ext4, size:3 3554432)
(device:/dev/block/mmcblk0p5, mount_point:/impdata, fs:ext4, size:83886 08)
(device:/dev/block/mmcblk0p6, mount_point:/cache, fs:ext4, size:3355443 2)
(device:/dev/block/mmcblk0p7, mount_point:/userdata, fs:ext4, size:2516 5824)
(device:/dev/block/mmcblk0p8, mount_point:/persist, fs:ext4, size:83886 08)
(device:/dev/block/mmcblk0p9, mount_point:/rtdata, fs:ext4, size:167772 16)
(device:/dev/block/mmcblk0p10, mount_point:/tclconfig, fs:ext4, size:33 554432)
(device:/dev/block/mmcblk0p11, mount_point:/vendor, fs:ext4, size:13958 67648)
(device:/dev/block/mmcblk0p12, mount_point:/system, fs:ext4, size:12884 91008)
(device:/dev/block/mmcblk0p13, mount_point:/data, fs:ext4, size:2147483 647)
skipping malformed layout.txt line: #define TAG 0
skipping malformed layout.txt line: #define PROCESS_INFO " START_BURN "
0 /frp ext4 /dev/block/mmcblk0p1 NULL 0 1048576
1 /misc ext4 /dev/block/mmcblk0p2 NULL 0 8388608
2 /res ext4 /dev/block/mmcblk0p3 NULL 0 16777216
3 /optee_armtz ext4 /dev/block/mmcblk0p4 NULL 0 33554432
4 /impdata ext4 /dev/block/mmcblk0p5 NULL 0 8388608
5 /cache ext4 /dev/block/mmcblk0p6 NULL 0 33554432
6 /userdata ext4 /dev/block/mmcblk0p7 NULL 0 25165824
7 /persist ext4 /dev/block/mmcblk0p8 NULL 0 8388608
8 /rtdata ext4 /dev/block/mmcblk0p9 NULL 0 16777216
9 /tclconfig ext4 /dev/block/mmcblk0p10 NULL 0 33554432
10 /vendor ext4 /dev/block/mmcblk0p11 NULL 0 1395867648
11 /system ext4 /dev/block/mmcblk0p12 NULL 0 1288491008
12 /data ext4 /dev/block/mmcblk0p13 NULL 0 2147483647
mount: mounting /dev/block/mmcblk0p3 on /res failed: Device or resource busy
mount /res ok
[loadExternalLink:3003]: Can't open /res/recovery.vold
mount /vendor ok
umount /vendor ok
[main:3843]: ====== Detect /tmp/factory/recovery Failed, go to checking phase2 = =====
[main:3844]: command:
[main:3845]: recovery:
[main:3887]: ====== Checking mount cmd:mount -t ext4 /dev/block/mmcblk0p6 /cach e ======
[main:3949]: ====== Checking umount cmd:umount /cache ======
argc = 2
argv = /sbin/factory save
0+1 records in
0+1 records out
312 bytes (312B) copied, 0.000162 seconds, 1.8MB/s
command:/bin/busybox dd if=/sys/realtek_boards/system_parameters of=/tmp/str.txt , (line=207) [file=src/rtk_common.cpp], ret(0)
command:/bin/busybox mkdir -p /tmp/factory, (line=322) [file=src/rtk_factory.cpp ], ret(0)
[INSTALL INFO][src/rtk_factory.cpp][325] gfactory_start = 5400000
[INSTALL INFO][src/rtk_factory.cpp][326] gfactory_block_size = 400000
[INSTALL INFO][src/rtk_factory.cpp][327] gfactory_size = 400000
[INSTALL INFO][src/rtk_factory.cpp][328] gerasesize = 200
[INSTALL INFO][src/rtk_factory.cpp][196] pp_ok = 3 current_pp = 1 seq_num = 6971 tarsize =2088960
tar: removing leading '/' from member names
command:/bin/busybox tar cf /tmp/factory.tar /tmp/factory, (line=645) [file=src/ rtk_factory.cpp], ret(0)
[INSTALL INFO][src/rtk_factory.cpp][651] *****************
ret = 512
ret = 512
[INSTALL INFO][src/rtk_factory.cpp][653] *****************
[INSTALL INFO][src/rtk_factory.cpp][668] save to current_pp = 0 seq_num = 6972
100 |******************************| 2041 KB
total_time:0 secands
command:/bin/busybox rm /tmp/factory.tar, (line=711) [file=src/rtk_factory.cpp], ret(0)
[INSTALL INFO][src/rtk_common.cpp][403] remove factory lock success
[main:3983]: /sbin/factory save
[main:4030]: modprobe xhci-hcd
modprobe: module 'xhci_hcd' not found
[main:4034]:
>>>>>> loader start! (May 6 2019:17:32:20, version=00.01.01)
[main:4038]: do ln -s /mmnt/sdcard/mmcblk1p1 /storage/ssdcard
Waiting for external usb disk...0s!
Waiting for external usb disk...1s!
Waiting for external usb disk...2s!
Waiting for external usb disk...3s!
Waiting for external usb disk...4s!
|
Файлы
Прошивки
Продажа
Литература
Статьи
Для просмотра сообщения Вы должны быть Участником форума. Для этого Вам необходимо 
Зарегистрировано всего