Прошил 40" с правкой формата лвдс в загрузчике через терминал.

Алексей, подскажите как сделать такую правку, с помощью чего? - у меня тоже 40я панель этой модели.
спасибо заранее!

lexa_p, как остановить загрузчик через терминал?

Прошил BBK 32LEX5043 а пульт подошел от JVC.

Подошла на Mystery MTV-3220HT2

Подскажите что делать, прогресс прошивки с флешки прошел до конца но после перезагрузки тел не включился. при включении флешка мигает раз и все. реакции больше никакой нет. Как побороть ситуацию без программатора?

Прошивка рабочая прошил тв который висел на заставке, флешки больше 2гб, тв не подхватывает!

всем привет изо перевернуто и не реагирует на пульт

Здравствуйте. таже проблема. не нашли решение ?

Всем привет. Подобный телевизор KraftA32H01DA7WL майн HK.T.RT2841P638 панель: WH32L147G22 Принесли после мастера, говорят прошить надо. Симптомы: при включении загрузка на логотипе или доходило до кругов, а потом помехи на экране. Померил электролиты, напряжения, в норме. Попробовал прошить этой прошивкой, процесс загрузки пошёл, а потом завис, так же с помехой на экране. После поменял кварц., зависание пропало, теперь включается логотип и всё. Прошивка тоже не идёт. Подключился терминалом, снял лог. Что лог показывает, не понял. Подскажите, куда дальше копать?

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2023.02.20 21:09:46 =~=~=~=~=~=~=~=~=~=~=~=
$
Hello world, 284x!{uni}[WEI]
svn: (Aug 14 2019 20:39:14)
flash_type = 2, secure_type = 2
b8062204=0
[go kb]KRRRR$
Hello world, 284x!{uni}[WEI]
svn: (Aug 14 2019 20:39:14)
flash_type = 2, secure_type = 2
b8062204=100
[go kb]KRRRROOOONNRRNNURU"U#U$

U-Boot 2012.07-branches/SQY/2831_Hikeen_1222_SVN9254/bootcode-svn23577 (Aug 14 2019 - 20:39:39) r-

[ENV] Writing to Factory...
$
Hello world, 284x!{uni}[WEI]
svn: (Aug 14 2019 20:39:14)
flash_type = 2, secure_type = 2
b8062204=1200
[go kb]KRRRROOOONNNNRRURU"U#U$

U-Boot 2012.07-branches/SQY/2831_Hikeen_1222_SVN9254/bootcode-svn23577 (Aug 14 2019 - 20:39:39) r-

Mac Address use 7c:82:74:24:49:fb in factory_ro
[ENV] Writing to Factory...
$
Hello world, 284x!{uni}[WEI]
svn: (Aug 14 2019 20:39:14)
flash_type = 2, secure_type = 2
b8062204=2300
[go kb]KRRRROOOONNRNNRRUU"U#U$

U-Boot 2012.07-branches/SQY/2831_Hikeen_1222_SVN9254/bootcode-svn23577 (Aug 14 2019 - 20:39:39) r-

Mac Address use 7c:82:74:24:49:fb in factory_ro
[ENV] Writing to Factory...
$
Hello world, 284x!{uni}[WEI]
svn: (Aug 14 2019 20:39:14)
flash_type = 2, secure_type = 2
b8062204=3400
[go kb]KRRRROOOONNRNRNURU"U#U$

U-Boot 2012.07-branches/SQY/2831_Hikeen_1222_SVN9254/bootcode-svn23577 (Aug 14 2019 - 20:39:39) r-

Mac Address use 7c:82:74:24:49:fb in factory_ro
[ENV] Writing to Factory...
$
Hello world, 284x!{uni}[WEI]
svn: (Aug 14 2019 20:39:14)
flash_type = 2, secure_type = 2
b8062204=4500
[go kb]KRRRROOOONNRNNURRU"U#U$

U-Boot 2012.07-branches/SQY/2831_Hikeen_1222_SVN9254/bootcode-svn23577 (Aug 14 2019 - 20:39:39) r-

Mac Address use 7c:82:74:24:49:fb in factory_ro
[ENV] Writing to Factory...
$
Hello world, 284x!{uni}[WEI]
svn: (Aug 14 2019 20:39:14)
flash_type = 2, secure_type = 2
b8062204=5600
[go kb]KRRRROOOONNRRNNRUU"U#U$

U-Boot 2012.07-branches/SQY/2831_Hikeen_1222_SVN9254/bootcode-svn23577 (Aug 14 2019 - 20:39:39) r-

Mac Address use 7c:82:74:24:49:fb in factory_ro
[ENV] Writing to Factory...
factory_tarsize = 0x32f200
[FAC] factory_save: MMC
[FAC] Save to eMMC (blk#:0x12000, buf:0x23900000, len:0x32f400)
[FAC] Save to eMMC (seq#:0xb503a, pp:1)
done
Factory Address:0x2000000, Size:0x800000!
Factory Read Only Address:0x1800000, Size:0x400000!

[1;41<<<<<<<<<<panel_filename NULL>>>>>>>>>> [m
==== James panel000 env_panel_set_default line:293 file=env_panel.c panel_select=<NULL>Panel: SD_panel_VESA_VFLIP.h
[WARN] para_no is 39 > 32. Clear more pcb_parameter env.
logbuf fifo[0] [buffer=1ca0e000], [size=10000]
logbuf fifo[1] [buffer=1ca1e000], [size=2000]
logbuf fifo[2] [buffer=1ca20000], [size=10000]
logbuf fifo[3] [buffer=1ca30000], [size=10000]
logbuf fifo[4] [buffer=1ca40000], [size=10000]
logbuf fifo[5] [buffer=1ca50000], [size=20000]
logbuf fifo[6] [buffer=1ca70000], [size=10000]
SCPU2: BISR hold remap
SCPU2: BISR ok 0
In: serial
Out: serial
Err: serial
Net: r8168: REALTEK RTL8168 @0x18016000
panel_init_1st 0529_1022
Hit Esc or Tab key to enter console mode or rescue linux: 0
Core IDDQ = 46 mA
IDDQ / High VID, and Core IDDQ= 46
Start Boot Setup ...
s_cmdline(0) = ""
s_cmdline(0) = ""
s_cmdline(0) = ""
FW Table to 0x0e900000, size=0x00000800 (0x0e900800)
FW Table fr 0x03800000, fw count: 50
[OK] fw_entry[0] offset = 0x8000 length = 0x1709100 (paddings = 0x1c00000) act_size = 0 part_num = 0
[OK] fw_entry[1] offset = 0x1c08000 length = 0x21bf08 (paddings = 0x500000) act_size = 0 part_num = 0
[OK] fw_entry[2] offset = 0x2108000 length = 0x34fdb0 (paddings = 0x600000) act_size = 0 part_num = 0
Disp HTotal=1559, Htotal 4x alignment=1559
[OK] fw_entry[3] offset = 0x2708000 length = 0x58678 (paddings = 0xc00000) act_size = 0 part_num = 0
den_h_start=96, den_h_end=1462
[OK] fw_entry[4] offset = 0x3308000 length = 0x2a3000 (paddings = 0x2a3000) act_size = 0 part_num = 0
[uzu] dvtotal(b8028504 = 325)
Normal boot fw follow...
[uzu] dhtotal(b8028508 = 6170617)
Linux Kernel:
[uzu] dh den start(b8028518 = 6005b6)
FW Image to 0x00108000, size=0x01709100 (0x01811100)
[uzu] dv den start(b802851c = 130313)
FW Image fr 0x03808000 (non-lzma)
[uzu] uzudtg control (b8028500 = 80000051)
Audio FW 1:
[memc] dvtotal(b8028604 = 325)
FW Image to 0x9a500000, size=0x0021bf08 (0x9a71bf08)
[memc] dhtotal(b8028608 = 6170617)
FW Image fr 0x05408000 (non-lzma)
[memc] dh den start(b802861c = 6005b6)
[memc] dv den start(b8028618 = 130313)
[memc] uzudtg control (b8028100 = 50000)
###### SFG_SFG_CTRL_0_reg : 0 ########
###### 1. 0xB802D9B8 : 0 ########
##### drvif_clock_set_dclk : 75400000 ###########

After Mapping (ulFreq:603200000) (div:8)======
dclk_Temp:670222
nMCode:67, f_code:45
Panel: ulFreq:603200000, nDPLL:0, Mcode:67, Ncode:3, offset:0

#### 0xb8000208[7e]

#### [drvif_clock_set_dtg_uzu_div]

#### 0xb8000208[400007e]

#### [drvif_clock_set_dtg_memc_div]
=== Panel Type : 0 ===
====284x panel_lvds_tx =====
=== Panel Index : 0 ===
======================================================
panel_init_2nd
the first 32-byte encrypted data(base=0x0b000000)
pwm_freq_hz = 25000
000 :rtk_hw_get_divider M_best:0 N_best:3 freq:25000 totalcnt:269 duty_max:255
e5M = 0x0
e1N = 0x3
db [1;32m reg 0x1801bcd0=0x80000003 [m
64 [1;32m reg 0x1801bcd4=0x87010d [m
73 [1;32m reg 0x1801bccc=0xe0000000 [m
b3 4c 47 7a 1f 3d e1 b6 2e 9b 44
010 : d7 3c 01 c2 b2 51 0c 0a ee 98 0a f9 25 32 49 1b
======================================================
the first 32-byte decrypted data(base=0x1a500000)
000 : 10 00 00 63 00 00 00 00 10 00 00 61 00 00 00 00
010 : 5f 5f 67 68 73 65 6e 64 5f 62 73 73 9a 73 25 f2
sw sha256 ret 0
Video FW 1:
FW Image to 0x9a900000, size=0x0034fdb0 (0x9ac4fdb0)
FW Image fr 0x05908000 (non-lzma)

======================================================
@@@[panel.c][1064][setPanel_sequence] (0xb8061930) = 0x00000000
the first 32-byte encrypted data(base=0x0b000000)
rtc wakeup: isRtcWakeUp=0
000 : 62 54 d4 0f 8a 20 cf ba aa ab c6 a6 2b 4b d8 39
010 : 8d 24 08 f5 81 f2 c3 19 a5 ea 7c 9f 87 f6 9f 40
======================================================
the first 32-byte decrypted data(base=0x1a900000)
000 : 10 00 00 63 00 00 00 00 10 00 00 61 00 00 00 00
010 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
sw sha256 ret 0
TEE FW target_addr = 0x16008000
KCPU FW:
(skip)
show raw video raw file ddr 0x84f00000 len 0x302a00
FW Image to 0x84f00000, size=0x002a3000 (0x851a3000)
FW Image fr 0x06b08000 (non-lzma)
GDMA: init with addr =051a3000
GDMA_init_module, 1st onlineProgDone=0x4f
GDMA_init_module, 1st passed
GDMA_init_module, 2nd onlineProgDone=0x4f
GDMA_init_module, 2nd passed
GDMA module_init finish
ampinit at panel flow, 4246
Hold HW semaphore
Await bypass unmute
ACPU1: BISR testing ....
ACPU1 BISR status: ok
Release HW semaphore
A1go [ADSP] bf [SB2_INSTAT] = 0x00000000
[ADSP] af [SB2_INSTAT] = 0x00000000
[ADSP]
[ADSP] -------------------
[ADSP] Audio Version = 1011820 (mac5p)
[ADSP] SHA-1: fa30687
[ADSP] Common Version = 1000847
[ADSP] SHA-1: be0c1d5
[ADSP] Binary src compiled at Mar 15 2018 16:06:01
[ADSP] Note = SQA_DailyBuild
[ADSP] -------------------

HDMI Raw Enable: MPG AC3 DTS MPEG2 AAC DDP WMAPRO MLP

SPDIF Raw Enable: MPG AC3 DTS MPEG2 AAC DDP WMAPRO MLP
[ADSP] __imem_text_start = 0x9a650000, size = 3904
[ADSP] [BOOT_AIO] shared-mem = 0xa0001030
[ADSP] [BOOT_AIO] magic_num = 0x24520000
[ADSP] [BOOT_AIO] version_code = 0x00000004
[ADSP] [BOOT_AIO] PAHSoSl!d mHaWg isce_nmuampbheorre
=
E n0ax2b4l5e2 0V0C0P0U
1

[
AVwait VDCSPP]U 1[:B OBOITS_RA IteOs]t[i1n]g .0.x0.0.0
0
0050
V
C[APDU1S P]B I[SBRO OsTta_tAuIsO:] [o2]k

R0xe0l0e0a0s0e0 0H0W

s[AeDmSaPp]h o[reB OaOgTa_iAnI
O]
V1go [3] 0x00000048
[E[ArDiScP]][F W[B]O dOiTs_ApI_Oi]n[itS ] cWlaosren inirgq! eBnooabtCloe de 0xc2on0f00ig00 weo9n
't be apply
[ADSP] [BOOT_AIO][PATH] get info from bootcode!
[ADSP] [BOOT_AIO][PATH] src_sel_headphone = 0x00000001
[ADSP] [BOOT_AIO][PATH] src_sel_aio1 = 0x00000001
[ADSP] [BOOT_AIO][PATH] src_sel_aio2 = 0x00000f40
[ADSP] [BOOT_AIO][POW] use default setting( 0x000001f8)!
[ADSP] [BOOT_AIO][DVC] use default setting!
[ADSP] [BOOT_AIO][DAC] dac0 source = 0x00000003
[ADSP] [BOOT_AIO][DAC] dac1 source = 0x00000003
[ADSP] af:mt 0x0000003f
[ADSP] af:mt 0x0000003f
[ADSP] af:mt 0x0000003f
[ADSP] af:mt 0x0000003f
[ADSP] af:mt 0x0000003f
[ADSP] DAC0 pcm source=3
[ADSP] DAC1 pcm source=3
[ADSP] [AIO][SPDIFO_0] reg= 0xc1800000
[ADSP] [AIO][SPDIFO_0] reg= 0x02800000
[ADSP] [SPDIF] NOISE_PROTECTION, disable SPDIF output
[ADSP] [AIO][SPDIFO_1] reg= 0xc1800000
[ADSP] [AIO][SPDIFO_1] reg= 0x02800000
[ADSP] af:umt 0x0000003f
[ADSP] [ao_Init] ver_magic
[ADSP] [AIO] SPDIF0-O: TS_AF_DVC
[ADSP] [AIO] SPDIF1-O: TS_AF_DVC
[ADSP] [AIO] I2S-O : PB_AF_AVC2
[ADSP] [AIO] DAC0 : PB_AF_AVC2
[ADSP] [AIO] DAC1 : PB_AF_AVC2
[ADSP] [PowerOnMusic] No Power On Music

======================================================
the first 32-byte encrypted data(base=0x0b000000)
000 : c0 c2 58 bb d8 b1 1a cf fc 6d 23 4f 02 d4 d7 b7
010 : b4 80 c4 9a d6 77 24 4c 3f 92 79 0e 1f 45 84 9d
======================================================
the first 32-byte decrypted data(base=0x00108000)
000 : b0 4f 10 ee 01 5c 04 e2 01 0c 55 e3 04 00 00 0a
010 : 03 40 04 e2 00 00 54 e3 16 00 00 0a 01 00 54 e3
sw sha256 ret 0
[ERR] Verify_SHA256_hash: hash value not match
======================================================
hash 1(base=0x12c00000)
000 : 72 d7 5e 04 4a 5a e8 bf 3a 0b a7 86 d2 9e a7 35
010 : 26 9a 6d 25 7c 3f e2 23 04 05 a3 3a e6 4f 8d f9
======================================================
hash 2(base=0x12c00200)
000 : 84 4d 14 8f 5f f1 71 ed 41 af 7c 9d ab 20 b9 1f
010 : 80 65 e5 30 74 23 5a 49 93 92 0b 27 f6 57 3b e0
[ERR] rtk_plat_read_kernel_image_from_eMMC: verify hash fail(-2)

==== IO_Set(PIN_AMP_MUTE, 0);
Enter console mode, disable watchdog ...

Realtek>

светодиод мигает синий/красный