BOOTSPI
BIST0_OK
_OK!decomp
_done
done
[AT][MB][start ub][0]

U-Boot 2011.06 (Jun 23 2022 - 10:49:17) MBOT-1106.0.10.936a0fd.201806111716

DRAM: 256 MiB

Hello U-Boot
Stack Pointer at: 836D5400
mem initial, start 0x82CEE180, len 0x402000
SPI: uboot held at [8F000000~90000000]
Now running in RAM - U-Boot at: 830F0180
In: serial
Out: serial
Err: serial
IIC port == 1
MDrv_IIC_Init PORT 1
MDrv_IIC_InitPort0: OK

RT500_Init RF No:21 Freq:474000 SoundType:3
IIC port == 1
MDrv_IIC_Init PORT 1
MDrv_IIC_InitPort0: OK
R500 11 coo
R500 coo

@@@[main_loop][297]@@@
hdcp key err

Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part

no_usb_connect

Changelist: 00112233
============= set bootargs ===============
WDT is not Enable !!!setenv WDT_ENABLE 1 to enable it.
Hit any key to stop autoboot: 0
enable dont overwrite function
AC on
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
FAIL : can not init usb!!
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
WDT is not Enable !!!setenv WDT_ENABLE 1 to enable it.
AC on
Unknown command 'unlockcmi' - try 'help'
[AT][MB][JPD Decode][0]
spi_rdc 0x80B00000 0xb000 0x400
offset 0xB000, size 0x400
spi_rdc 0x80B00000 0x5d000 0x400
offset 0x5D000, size 0x400
setenv bootcmd ' usb exit;spi_rdc 0x80b00000 0x5d01c 0x284204; LzmaDec 0x80b00000 0x284204 0x80000180 0x81000000; go 0x80000224;
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
USB is stopped. Please issue 'usb start' first.
offset 0x5D01C, size 0x284204

LZMA Decompression...CRC check success !!
ok

k5ap# printenv
51OnRam=0
AP_SW_MODEL=0x0001
AP_SW_VERSION=0x0001
CM_DVBT_ADDR=0x003e8000
CM_DVBT_ORDER=0x003e6000
CM_DVBT_SIZE=0x00015000
CUSTOMER_OUI=0x169B
HW_MODEL=0x0001
HW_VERSION=0x0001
MstarUpgrade_complete=0
OAD_IN_MBOOT=1
RF_No=21
RF_Sound=3
UARTOnOff=on
baudrate=115200
bl_dfb_framebuffer_addr=0x01b28000
bl_jpd_inter_addr=0x02418800
bl_jpd_inter_size=0x00630000
bl_jpd_read_addr=0x01f1c800
bl_jpd_read_size=0x00100000
bl_jpd_write_addr=0x0201c800
bl_jpd_write_size=0x003fc000
bootargs=BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x3FE000 ENV_VAR_SIZE=0x1000 ENV=SERIAL SECURITY=OFF
bootcmd=usb exit;spi_rdc 0x80b00000 0x5d01c 0x284204; LzmaDec 0x80b00000 0x284204 0x80000180 0x81000000; go 0x80000224;
bootdelay=0
bootscript=echo Running bootscript from mmc${mmcdev} ...; source ${loadaddr}
burnmode_poweron=false
console=ttyS2,115200n8
dc_poweroff=0
factory_poweron_mode=direct
hdmicolor=9
info_exchange=spi
loadaddr=0x82000000
loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr
loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage
mmcargs=setenv bootargs console=${console} vram=${vram} root=${mmcroot} rootfstype=${mmcrootfstype}
mmcboot=echo Booting from mmc${mmcdev} ...; run mmcargs; bootm ${loadaddr}
mmcdev=0
mmcroot=/dev/mmcblk0p2 rw
mmcrootfstype=ext3 rootwait
osd_language=English
panel_cmd=12
resolution=8
stderr=serial
stdin=serial
stdout=serial
tv_format=6
ubispeedup=UBI
upgrade_mode=null
usbtty=cdc_acm
ve_buffer_addr=0x02a48800
ve_buffer_size=0x0021c000
vram=16M

BOOTSPI
BIST0_OK
_OK!decomp
_done
done
[AT][MB][start ub][0]

U-Boot 2011.06 (Feb 19 2020 - 16:30:58) MBOT-1106.0.10.936a0fd.201806111716

DRAM:
Hello U-Boot
Stack Pointer at: 83627740
mem initial, start 0x82CEE180, len 0x402000
SPI: uboot held at [8F000000~90000000]
Now running in RAM - U-Boot at: 830F0180
In: serial
Out: serial
Err: serial
[ERROR] do_spi_init_partition:1221: This function doesn't support
============= set bootargs ===============
Unknown command 'panel_pre_init' - try 'help'
[AT][MB][JPD Decode][0]
spi_rdc 0x80B00000 0xB000 0x400
offset 0xB000, size 0x400
spi_rdc 0x80B00000 0x35000 0x400
offset 0x35000, size 0x400
setenv bootcmd ' usb exit;spi_rdc 0x80B00000 0x3501C 0x28CA56; LzmaDec 0x80B00000 0x28CA56 0x80000180 0x81000000; go 0x80000224;
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase

@@@[main_loop][297]@@@
============= set bootargs ===============
Hit any key to stop autoboot: 0
enable dont overwrite function
Boot Check: Reboot by WDT --------
AC on
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x3604000
[USB] Reg 0x28: 0x4000 0x360
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 9:
Wait for hub reset....
checking hub ports...
[USB] control1 max:40

[USB] interface[0] conf:1 value 8:
2 USB Device(s) found
scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found
USB device specified [0]
USB partition specified [1]
reading MstarUpgrade.bin

1 bytes read
USB device specified [0]
USB partition specified [1]
reading /SbootUpgrade.bin

** Unable to read "/SbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /MbootUpgrade.bin

** Unable to read "/MbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /UrsaUpgrade.bin

** Unable to read "/UrsaUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /ForceUpgradeApp.bin

** Unable to read "/ForceUpgradeApp.bin" from usb 0:1 **
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Current state ->[0x8]
USB device specified [0]
USB partition specified [1]
reading MstarUpgrade.bin

1 bytes read
reading MstarUpgrade.bin

16384 bytes read
reading MstarUpgrade.bin

16408 bytes read
storage is empty
[ERROR] get_script_next_line:845: Error: the max size of one line is 1024!!!
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase

>> usb start 0
--28 %
(Re)start USB 0...
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x3604000
[USB] Reg 0x28: 0x4000 0x360
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 9:
Wait for hub reset....
checking hub ports...
[USB] control1 max:40

[USB] interface[0] conf:1 value 8:
2 USB Device(s) found
scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found

>> fatload usb 0 80B00000 dump.bin
--37 %
reading dump.bin

4194304 bytes read

>> spi_wrc 80B00000 0 400000
--46 %
offset 0x0, size 0x400000
initialization done!
Erasing...
Writing...
Verifying...

>> setenv usb_complete 1
--55 %

>> setenv usb_upgrade 0
--64 %

>> setenv upgrade_mode null
--73 %

>> setenv MstarUpgrade_complete 1
--82 %

>> saveenv
--91 %
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase

>> reset
--99 %
Reset command is skipped
[ERROR] get_script_next_line:845: Error: the max size of one line is 1024!!!
AP upgrade OK!~
All Upgrade File Had Finished !!
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
resetting ...

TV_RADIO = 0x15
FAV = 0x55
RECALL = 0x13
AUDIO = 0x51

UP = 0x06
POWER = 0x59
EXIT = 0x05
MENU = 0x45
DOWN = 0x16
LEFT = 0x5A
SELECT = 0x1A
RIGHT = 0x1B

0 = 0x0F
1 = 0x52
2 = 0x50
3 = 0x10
4 = 0x56
5 = 0x54
6 = 0x14
7 = 0x4E
8 = 0x4C
9 = 0x0C

MUTE = 0x19
PAGE+ = 0x11
PAGE- = 0x0D
INFO = 0x17
RED = 0X42
GREEN = 0x40
YELLOW = 0x00
BLUE = 0x03
TTX = 0x18
EPG = 0x4D

PREVIOUS = 0x08
NEXT = 0x0B
BACKWARD = 0x4A
FORWARD = 0x48
PLAY = 0X46
RECORD = 0x07
STOP = 0x04
PAUSE = 0x44
SUBT = 0x58
REPEAT = 0x12
GOTO = 0x0E