Terminal log file
Date: 23.12.2022 - 17:17:31
-----------------------------------------------
BI$
Hello world, 285o!{uni}[WEI][arm64]
svn:4a613103623ea907 (Dec 28 2018 13:43:11)
flash_type = 2, secure_type = 2
b8062204=a5
HW off: 146
ABCDE[RPMB]Auth Key is Ready!!! Test Print1 SB2_CTRL_REG_reg=0x0
Test Print1 SB2_CTRL_REG_reg=0x1
Test Print1 SB2_CTRL_REG_reg=0x0
Test Print1 SB2_CPU_FLASH_REGION=0xba20b820
[go atf]U

U-Boot 2012.07 (Jul 14 2020 - 18:21:55) r-343b10e

[ENV] Writing to Factory...
factory_tarsize = 0x1bac00
[FAC] factory_save: MMC
[FAC] Save to eMMC (blk#:0x14000, buf:0x23900000, len:0x1bae00)
[FAC] Save to eMMC (seq#:0x66e, pp:1)
done
Factory Address:0x2000000, Size:0x1000000!
Factory Read Only Address:0x1800000, Size:0x400000!
[abner] CusApi_env_relocate:32
[abner]: setenv avb value is from env set
longqi 16:, offset:0x1cdffbe00, size=0x4000000 mount_point=/smarttv filesystem=vfat partname=smarttv type=bz2!

SEC_FEATURE_SUPPORT=0x00000055.
TRIM mode

erasing...... (start=0x00000000

** Invalid Partitions to mount **
make_fs_entry failed
default pq file tmp/factory/bin_panel/PanelParam/vip_default_pq.bin exsit!

rce.xml ok!
------------parse tmp/factory/cpu_resource.xml ok!
panel initialize....
panel_init_1st 0529_1022
den_h_start=0, den_h_end=0
=== Panel Index : 0 ===
[TCON]No demand of TCON(outputgamma,valc,OD,demura) setting.
panel type 0 set swap:0
In: serial
Out: serial
Err: serial
Net: r8168: REALTEK RTL8168 @0x18016000
wov state=0
Hit Esc or Tab key to enter console mode or rescue linux: 0

------------can't find tmp/factory/recovery

** Invalid boot device **
ac_on_update_mac_address:3067

ac_on_update_mac_address
ac_on_update_CI_key:3351
cikey.bin exist! No need CI key again!
ac_on_update_hdcp_key:3230
Error: reading boot sector
first_HDCP:
reading hdcpwrited.used
Error: reading boot sector
hdcp_file_name=HDCP/
reading HDCP/
Error: reading boot sector
read HDCP file fail
ac_on_update_hdcp_key22:3290
Error: reading boot sector
first_HDCP:
reading hdcp2writed.used
Error: reading boot sector
hdcp_file_name=HDCP2/
reading HDCP2/
Error: reading boot sector
read HDCP2 file fail
ac_on_update_SN_key:3422
Error: reading boot sector
first_SnKey:
reading snkey.used
Error: reading boot sector
snkey_file_name=SnPlusKey/
reading SnPlusKey/
Error: reading boot sector
file_fat_read failed!!!!!
ac_on_update_backlight_limit
reading panel_bl.txt
Error: reading boot sector
Can not find panel_bl.txt file[abner] check_usb_into_factory_mode:2018 check_usb_into_factory_mode

** Invalid boot device **
stopping USB..
abner hikeen_boot_update_mode = 0, hikeen_boot_power_update = 0, boot_mode = 2

====== boot_ac_on=1 ======

Start Boot Setup ...
FW Table to 0x06800000, size=0x00000a00 (0x06800a00)
FW Table fr 0x04000000, fw count: 50
[OK] fw_entry[0] offset = 0x8000 length = 0x1ab0df4 (paddings = 0x1ab0e00) act_size = 0 part_num = 0
[OK] fw_entry[1] offset = 0x1ab8e00 length = 0x1ff7c0 (paddings = 0x1ff800) act_size = 0 part_num = 0
[OK] fw_entry[2] offset = 0x1cb8600 length = 0x3d5bd8 (paddings = 0x3d5c00) act_size = 0 part_num = 0
[OK] fw_entry[3] offset = 0x208e200 length = 0x9f9d0 (paddings = 0x9fa00) act_size = 0 part_num = 0
[OK] fw_entry[4] offset = 0x212dc00 length = 0x5eec00 (paddings = 0x5eec00) act_size = 0 part_num = 0
Normal boot fw follow...
vFlipEnable 0 boot_av->bRotate 0
Linux Kernel:
FW Image to 0x00108000, size=0x01ab0df4 (0x01bb8df4)
FW Image fr 0x04008000 (non-lzma)
Audio FW 1:
FW Image to 0xdeaddead, size=0x001ff7c0 (0xdecdd66d)
FW Image fr 0x05ab8e00 (non-lzma)
Enter standby, skip this entry
Video FW 1:
FW Image to 0xdeaddead, size=0x003d5bd8 (0xdeeb3a85)
FW Image fr 0x05cb8600 (non-lzma)
Enter standby, skip this entry
TEE FW target_addr = 0x16008000
(skip)
show raw video raw file ddr 0x84f00000 len 0xec5e00
FW Image to 0x84f00000, size=0x005eec00 (0x854eec00)
FW Image fr 0x0612dc00 (non-lzma)
Enter standby, skip this entry
current avb status on
do_avb_init success!!!!!
current avb status on
## Android Verified Boot 2.0 version 1.1.0
[check_pmbr_LBA0][115]Current platfrom partition table format is not GPT!

[check_gpt_context][268]check pmbr LBA0 fail!

[init_global_gpt_partition_info][333]GPT context check fail!

[get_gpt_entry_by_name][407]parse gpt partition info fail!

MMC: block number 0x203d3dbd exceeds max(0xe90000)
emmc: transfer error!!! byte(xfer=0x00000000; targ=0x00010000
mmc_byte_io: sector read error
sw sha256 ret 0
[abner] set default uart closed !

EVer:3´1054373

(build:3ËJul 17 2019 3×13:36:23)