BI$
Hello world, 285o!{uni}[WEI]
****System Start****
[arm64]
svn:b9f213addb0a49a8 (Aug 5 2021 10:42:08)
flash_type = 2, secure_type = 2
b8062204=a5
wrong crc32, cur crc32_val = 603b0489, orig = 00000000
HW off: 0
ABCDEt.y.0.0 t.y.1.0 t.y.2.0 t.y.3.0 [F] 03 05 04 06
T.21
r.y.0
R.6
[RPMB]Auth Key not Ready(7)!!!
Test Print1 SB2_CTRL_REG_reg=0x0
Test Print1 SB2_CTRL_REG_reg=0x1
Test Print1 SB2_CTRL_REG_reg=0x0
Test Print1 SB2_CPU_FLASH_REGION=0xba20b820
[go atf]U

U-Boot 2012.07 (Aug 05 2021 - 10:40:52) r-Sync_20210524_105120-727-gb9f213addb0

[ENV] Writing to Factory...
factory_tarsize = 0x1ba400
[FAC] factory_save: MMC
[FAC] Save to eMMC (blk#:0x14000, buf:0x23900000, len:0x1ba600)
[FAC] Save to eMMC (seq#:0x78c, pp:1)
done
Factory Address:0x2000000, Size:0x1000000!
Factory Read Only Address:0x1800000, Size:0x400000!
[abner] CusApi_env_relocate:32
[abner]: setenv avb value is from env set
make_fs_entry init 1
1://smarttv.json Size: 10371 byte(s).
can not fount node [support]

set ir data to share memory by json config
1:/common/irmap/HKFAC.bin Size: 472 byte(s).
share memory for irmap <58/494>, 1:/common/irmap/HKFAC.bin register 58
irda_select_value1=7-hikeen
1:/common/irmap/HKSTD.bin Size: 368 byte(s).
share memory for irmap <103/494>, 1:/common/irmap/HKSTD.bin register 45
1:/common/irmap/ASANO_2619_DE40ERIS.bin Size: 464 byte(s).
share memory for irmap <160/494>, 1:/common/irmap/ASANO_2619_DE40ERIS.bin register 57
irda_select_value=5-hikeen

set keypad data to share memory by json config
range = 15
start = 210
channel = 0
function = 139
multi_function = 139
share memory for keypad <1/8>, adc0 register fd2000001 [210..15]
range = 12
start = 45
channel = 0
function = 108
multi_function = 108
share memory for keypad <2/8>, adc0 register c2d000001 [45..12]
range = 12
start = 76
channel = 0
function = 103
multi_function = 103
share memory for keypad <3/8>, adc0 register c4c000001 [76..12]
range = 12
start = 105
channel = 0
function = 549
multi_function = 549
share memory for keypad <4/8>, adc0 register c69000001 [105..12]
range = 12
start = 133
channel = 0
function = 105
multi_function = 105
share memory for keypad <5/8>, adc0 register c85000001 [133..12]
range = 12
start = 173
channel = 0
function = 106
multi_function = 106
share memory for keypad <6/8>, adc0 register cad000001 [173..12]
range = 20
start = 0
channel = 0
wakeup true
function = 116
multi_function = 116
share memory for keypad <7/8>, adc0 register 1001400000001 [0..20]

initial order config at bootcode by json config
fenghl -> pre_init_board_backlight
1://smarttv.json Size: 10371 byte(s).
fenghl -> backlight_limitation_switch = 0
fenghl -> PF7913
fenghl -> backlight_control_ic_type = 2
fenghl -> board_type = 2842
change PIN_BL_ADJ 0xb280fea861000107 to 0xb280fea861000107
change PIN_BL_ADJ 0xb280fea861000107 to 0xe480fea861000107
change PIN_BL_ADJ 0xe480fea861000107 to 0xe4fffea861000107
readusbfile 0
led_flash_when_boot_process: 1
led enum_pin_led_index: 0

set panel data by json config
1:/common/panel/ASANO_JE415D3HAOL_FHD_1712.fw Size: 140 byte(s).
[abner] get_factory_test:351 readusbfile = 0

(Re)start USB...
USB0: ----------- ehci_hcd_init -----------
#@# ehci_hcd_init(452) ehci mac0
----------- usb2_crt on(0) -----------
----------- usb2_crt -----------
----------- usb2_crt on(1) -----------
----------- usb2_crt -----------
[ehci], info, #@# usb2_phy_setting(335) +++ for usbphy setting 20170420
[ehci], info, #@# usb2_phy_setting(337) ---
----------- ehci_usb_mac_init -----------
USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Vendor specific, USB Revision 2.0
- Realtek 802.11n 64E003A1855B
- Class: (from Interface) Vendor specific
- PacketSize: 64 Configurations: 1
- Vendor: 0x0bda Product 0xf179 Version 0.0
Configuration: 1
- Interfaces: 1 Bus Powered Remote Wakeup 500mA
Interface: 0
- Alternate Setting 0, Endpoints: 3
- Class Vendor specific
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
- Endpoint 3 Out Bulk MaxPacket 512

abner file = cus_env_panel.c, func = HK_CusApi_env_setup_panel_parameter, line = 181 boot_lvds_map = -1, boot_lvds_depth = -1
abner file = cus_env_panel.c, func = HK_CusApi_env_setup_panel_parameter, line = 182 boot_swap_ab = -1
[heath]T2=30,T3=200,T4=200,T5=40,T6=1200
abner file = cus_env_panel.c, func = HK_CusApi_env_setup_panel_parameter_from_facro, line = 199 hk_save_to_factory_ro = 0
file 1:/common/pq/ASANO_JE415D3HAOL_FHD_1712_PQ.bin is decompress already
file 1:/common/pq/ASANO_JE415D3HAOL_FHD_1712_OSD.bin is decompress already
file 1:/common/pq/ASANO_JE415D3HAOL_FHD_1712_HDR.bin is decompress already
make_fs_exit exit 1
default pq file tmp/factory/bin_panel/PanelParam/vip_default_pq.bin exsit!
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Vendor specific, USB Revision 2.0
- Realtek 802.11n 64E003A1855B
- Class: (from Interface) Vendor specific
- PacketSize: 64 Configurations: 1
- Vendor: 0x0bda Product 0xf179 Version 0.0
Configuration: 1
- Interfaces: 1 Bus Powered Remote Wakeup 500mA
Interface: 0
- Alternate Setting 0, Endpoints: 3
- Class Vendor specific
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
- Endpoint 3 Out Bulk MaxPacket 512

read FactoryAutomation/EnableFactoryMode/EnableFactoryMode 0x200 bytes to check file exist ...

** Invalid boot device **
[WARN] check_file_in_usb:Read FactoryAutomation/EnableFactoryMode/EnableFactoryMode 0x200 bytes from USB failed. (0x1)

<<<<<<Panel: ASANO_JE415D3HAOL_FHD_1712>>>>>>>>

<<<<<<parameter_len: 140 >>>>>>>>
logbuf fifo[0] [buffer=1ca0e000], [size=10000]
logbuf fifo[1] [buffer=1ca1e000], [size=2000]
logbuf fifo[2] [buffer=1ca20000], [size=10000]
logbuf fifo[3] [buffer=1ca30000], [size=10000]
logbuf fifo[4] [buffer=1ca40000], [size=10000]
logbuf fifo[5] [buffer=1ca50000], [size=20000]
logbuf fifo[6] [buffer=1ca70000], [size=10000]
make_fs_entry init 1
------------parse tmp/factory/vsc_resource.xml ok!
------------parse tmp/factory/throttle_resource.xml ok!
------------parse tmp/factory/cpu_resource.xml ok!
make_fs_exit exit 1
panel initialize....
panel_init_1st 0529_1022
den_h_start=120, den_h_end=2040
=== Panel Index : 0 ===
[TCON]No demand of TCON(outputgamma,valc,OD,demura) setting.
panel type 0 set swap:0
In: serial
Out: serial
Err: serial
Net: r8168: REALTEK RTL8168 @0x18016000
wov state=0
Hit Esc or Tab key to enter console mode or rescue linux: 0

------------We will Enter Recovery Rescue
Watchdog: Disabled
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
key press can't locate adc
ac_on_update_mac_address:3269

ac_on_update_mac_address
ac_on_update_CI_key:3553
cikey.bin exist! No need CI key again!
ac_on_update_hdcp_key:3432
filename = HDCP
Error: reading boot sector
first_HDCP:
reading hdcpwrited.used
filename = hdcpwrited.used
Error: reading boot sector
hdcp_file_name=HDCP/
reading HDCP/
filename = HDCP/
Error: reading boot sector
read HDCP file fail
ac_on_update_hdcp_key22:3492
filename = HDCP2
Error: reading boot sector
first_HDCP:
reading hdcp2writed.used
filename = hdcp2writed.used
Error: reading boot sector
hdcp_file_name=HDCP2/
reading HDCP2/
filename = HDCP2/
Error: reading boot sector
read HDCP2 file fail
ac_on_update_SN_key:3624
filename = SnPlusKey
Error: reading boot sector
first_SnKey:
reading snkey.used
filename = snkey.used
Error: reading boot sector
snkey_file_name=SnPlusKey/
reading SnPlusKey/
filename = SnPlusKey/
Error: reading boot sector
file_fat_read failed!!!!!
image_name new
1://smarttv.json Size: 10371 byte(s).
get image_name install_2842_1GDDR.img
[abner] check_usb_into_factory_mode:2018 check_usb_into_factory_mode

** Invalid boot device **

** Invalid boot device **

** Invalid boot device **
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: Vendor specific, USB Revision 2.0
- Realtek 802.11n 64E003A1855B
- Class: (from Interface) Vendor specific
- PacketSize: 64 Configurations: 1
- Vendor: 0x0bda Product 0xf179 Version 0.0
Configuration: 1
- Interfaces: 1 Bus Powered Remote Wakeup 500mA
Interface: 0
- Alternate Setting 0, Endpoints: 3
- Class Vendor specific
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
- Endpoint 3 Out Bulk MaxPacket 512

read FactoryAutomation/EnableFactoryMode/EnableFactoryMode 0x200 bytes to check file exist ...

** Invalid boot device **
[WARN] check_file_in_usb:Read FactoryAutomation/EnableFactoryMode/EnableFactoryMode 0x200 bytes from USB failed. (0x1)

====== Enter into android recovery bEnterWipe=0 ======
abner hikeen_boot_update_mode = 0, hikeen_boot_power_update = 0, boot_mode = 1
ac_on_update_backlight_limit
reading panel_bl.txt
filename = panel_bl.txt
Error: reading boot sector
Error: FAT sector size mismatch (fs=12912, dev=0)
Can not find panel_bl.txt file
install image msg = tv_system=NULL imgfile_pattern=install_2842_1GDDR.img
image_name release

get header done
decrypt header size 16...
#############################
# Dump Rescue header:
# magic = 0x6331beef
# size = 0x00df3cbf (include header)
#############################
#############################
# Enter Rescue Linux:
# secure_mode = 3
# compressed = 1
# block_no = 0x00001000
# size_bytes = 0x00df3cbf
# target_addr = 0x00108000
#############################
read done
to decrypt...
decrypt rescue successful
sw sha256 ret 0
[ERR] Verify_SHA256_hash: hash value not match
[ERR] rtk_plat_run_rescue_from_eMMC: hash value not match
Enter console mode, disable watchdog ...