Кто богат на прошивку USB на данный аппарат ? Пришел с дефектом: включается- заставка логотипа- далее крутит Google TV пару минут и перезапуск. Пока ничего не читал. HR-MT9617 _ HK650WLEDM-EH2BH Лог такой.
[Mboot] ===== sw IR Config Register ===== [Mboot] ===== Attach IR Interrupt ====== Uboot Relocation: 152 MiB
eMMC HS400 5.1 200MHz eMMC 29.12 GB eMMC used life: 0~10% CID 0x00B9524A 0xB6390452 0x3444544A 0x42000115 DRAM : 3072MB SAR5=ON In: serial Out: serial Err: serial Net: No ethernet found. MAC: 0x18: 0x84: 0xC1: 0x1D:0x5: 0xF5 [AT][MBoot][Driver Init][851] mmc change mount : tvconfig ** File not found model.info [ERROR] vfs_getsize:449: ext4filesize mmc fail No enough buffer or path fail(model.info) : [src/MsUtility.c] [loadscript] model.info not find !! Clean model_info env Writing to MMC(0)... 128 blocks written: OK 128 blocks written: OK done Try virtual ab bootloader_control... 0:MCP_S_D4_2666_16G_4x 1:EXT_D4_2666_8G_4x DRAM Channel 0 Size = [4096MB] Try virtual ab bootloader_control...
Changelist: 24543697 do not first setup(first_setup=1), skip self adaption. ============= set bootargs =============== Hit any key to stop autoboot: 0 enable dont overwrite function AC on
Upgrade Version: 2.0
Writing to MMC(0)... 128 blocks written: OK 128 blocks written: OK done Check USB port[0]: [USB] config miu select [F0] [EF] [EF] ][EF] [USB] enable miu lower bound address subtraction Error, couldn't init Lowlevel part Check USB port[1]: [USB] config miu select [F0] [EF] [EF] ][EF] [USB] enable miu lower bound address subtraction Error, couldn't init Lowlevel part Check USB port[2]: [USB] config miu select [F0] [EF] [EF] ][EF] [USB] enable miu lower bound address subtraction scanning bus for devices... New Device 0
[USB] interface[0] conf:1 value E0: 1 USB Device(s) found Found USB WIFI [MTK7663] in usb port 2 scanning bus for storage devices... 0 Storage Device(s) found Check USB port[3]: [USB] config miu select [F0] [EF] [EF] ][EF] [USB] enable miu lower bound address subtraction Error, couldn't init Lowlevel part FAIL : can not init usb!! Writing to MMC(0)... 128 blocks written: OK 128 blocks written: OK done mmc change mount : project_id Size of file "project_id.ini" from mmc device 0 partition project_id: 294 bytes Loading file "project_id.ini" at offset 0x0 from mmc device 0 partition project_id 294 bytes read [Mboot_IR] boot from dynamic ir Try virtual ab bootloader_control... ENV_UPGRADE_COMPLETE =0 ENV_UPGRADE_MODE =null androidboot boot reason =reboot Writing to MMC(0)... 128 blocks written: OK 128 blocks written: OK done [QHB] PowerOnMode = 255, u4BootCtrl = 0x0, fgStateOn = 1 [QHB] prepare to CLEAR QHB [QHB] not quiescent boot. AC on ** CEC [TV] Change this Vendor ID according to customerWriting to MMC(0)... 128 blocks written: OK 128 blocks written: OK done findUsbDevice: find mtk bt usb device from usb prot[2] Check USB port[2]: [USB] config miu select [F0] [EF] [EF] ][EF] [USB] enable miu lower bound address subtraction scanning bus for devices... New Device 0
[USB] interface[0] conf:1 value E0: 1 USB Device(s) found Found USB WIFI [MTK7663] in usb port 2 Ldbtusb_connect: Ldbtusb_connect begin Ldbtusb_connect: dev->endpoints[0].bmAttributes = 0x3 Ldbtusb_connect: dev->endpoints[0].bEndpointAddress = 0x81 Ldbtusb_connect: set endpoints[0] to intr_ep Ldbtusb_connect: dev->endpoints[1].bmAttributes = 0x2 Ldbtusb_connect: dev->endpoints[1].bEndpointAddress = 0x82 Ldbtusb_connect: set endpoints[1] to bulk_rx_ep Ldbtusb_connect: dev->endpoints[2].bmAttributes = 0x2 Ldbtusb_connect: dev->endpoints[2].bEndpointAddress = 0x2 Ldbtusb_connect: set endpoints[2] to bulk_tx_ep LD_btmtk_usb_probe: ========================================= LD_btmtk_usb_probe: Mediatek Bluetooth USB driver ver 4.0.22081001 LD_btmtk_usb_probe: ========================================= LD_btmtk_usb_probe: probe_counter = 1 LD_btmtk_usb_probe: data address = 2860CCC8 btmtk_usb_cap_init: chip id = 7663 btmtk_usb_cap_init: patch name: mt7663_patch_e2_hdr.bin btmtk_usb_cap_init: woble setting file name is woble_setting_7663.bin mtk_patch_bin_patch: /firmware/bt_7663.cfg bt_env is NULL mmc change mount : cusdata ** File not found /firmware/bt_7663.cfg [ERROR] vfs_getsize:449: ext4filesize mmc fail LD_load_code: Get file size fail mmc change mount : tvconfig ** File not found /firmware/bt_7663.cfg [ERROR] vfs_getsize:449: ext4filesize mmc fail LD_load_code: Get file size fail ** Bad Signature on 0:48: expected 0x5840, got 0x0000 LD_load_code: vfs_mount vendor fail mmc change mount : userdata Failed to mount ext2 filesystem... ** Bad ext4 partition or disk - mmc 0:47 ** [ERROR] vfs_getsize:449: ext4filesize mmc fail LD_load_code: Get file size fail ** Bad Signature on 0:48: expected 0x5840, got 0x0000 LD_load_code: vfs_mount system fail ** Bad Signature on 0:48: expected 0x5840, got 0x0000 LD_load_code: vfs_mount APP fail btmtk_usb_load_bt_cfg: bt_7663.cfg not exist in the /vendor/firmware mtk_patch_bin_patch: /firmware/bt.cfg bt_env is NULL mmc change mount : cusdata Size of file "/firmware/bt.cfg" from mmc device 0 partition cusdata: 1015 bytes Loading file "/firmware/bt.cfg" at offset 0x0 from mmc device 0 partition cusdata 1015 bytes read btmtk_usb_load_bt_cfg_item: bt_cfg_content->support_unify_woble = 1 btmtk_usb_load_bt_cfg_item: bt_cfg_content->unify_woble_type = 1 btmtk_usb_load_fw_cfg_setting: btmtk_usb_load_fw_cfg_setting: find no next block, check bt cfg!btmtk_usb_load_fw_cfg_setting: btmtk_usb_load_fw_cfg_setting: search_result is NULLbtmtk_usb_load_fw_cfg_setting: WMT_CMD000: found & stored in 0 btmtk_usb_parse_bt_cfg_file: Can't find LD_DL_WIFI_ENABLE btmtk_usb_load_bt_cfg_item: search item LD_DL_WIFI_ENABLE is invalid! btmtk_usb_load_bt_cfg: btmtk_usb_load_bt_cfg_item error return -1 mtk_patch_bin_patch: /firmware/mt7663_patch_e2_hdr.bin bt_env is NULL mmc change mount : cusdata Size of file "/firmware/mt7663_patch_e2_hdr.bin" from mmc device 0 partition cusdata: 278558 bytes Loading file "/firmware/mt7663_patch_e2_hdr.bin" at offset 0x0 from mmc device 0 partition cusdata 278558 bytes read btmtk_usb_check_need_load_patch_7668: btmtk_usb_check_need_load_patch_7668: return len is 7 btmtk_usb_load_rom_patch_7668: patch_status: 2, retry: 20 btmtk_usb_send_wmt_cfg: send wmt cmd! btmtk_usb_send_wmt_cmd: CMD: 6F FC 06 01 06 02 00 03 01 btmtk_usb_send_wmt_cmd: EVT: E4 05 02 06 01 00 00 btmtk_usb_load_rom_patch_7668: FW Version = 2305111231b235a btmtk_usb_load_rom_patch_7668: build Time = 2305111231b235a btmtk_usb_load_rom_patch_7668: platform = 7663 btmtk_usb_load_rom_patch_7668: HW/SW version = mp-1 btmtk_usb_load_rom_patch_7668: btmtk_usb_load_rom_patch_7668: loading rom patch of ILM btmtk_usb_load_partial_rom_patch_7668: loading rom patch... Done btmtk_usb_send_wmt_reset_cmd: Check reset wmt result : OK Ldbtusb_connect: usbbt probe success Ldbtusb_connect: Ldbtusb_connect end LD_btmtk_usb_SetWoble: btmtk_usb_send_wmt_cmd: retry to get event(10) btmtk_usb_send_wmt_cmd: retry to get event(9) btmtk_usb_send_wmt_cmd: retry to get event(8) btmtk_usb_send_wmt_power_on_cmd_7668: OK usb_bt_interrupt_msg: epType = 0x2 usb_bt_interrupt_msg: ret = 0x0 btmtk_usb_send_hci_tci_set_sleep_cmd_7668: OK usb_bt_interrupt_msg: epType = 0x2 usb_bt_interrupt_msg: ret = 0x0 btmtk_usb_send_hci_reset_cmd: OK usb_bt_interrupt_msg: epType = 0x2 usb_bt_interrupt_msg: ret = 0x0 btmtk_usb_get_vendor_cap: OK usb_bt_interrupt_msg: epType = 0x2 usb_bt_interrupt_msg: ret = 0x0 btmtk_usb_send_read_bdaddr: ADDR: A8-16-9D-8C-35-79 mtk_patch_bin_patch: /firmware/woble_setting_7663.bin bt_env is NULL mmc change mount : cusdata Size of file "/firmware/woble_setting_7663.bin" from mmc device 0 partition cusdata: 1640 bytes Loading file "/firmware/woble_setting_7663.bin" at offset 0x0 from mmc device 0 partition cusdata 1640 bytes read btmtk_usb_load_fw_cfg_setting: APCF00: found & stored in 0 btmtk_usb_load_fw_cfg_setting: APCF01: found & stored in 1 btmtk_usb_load_fw_cfg_setting: APCF_ADD_MAC00: found & stored in 0 btmtk_usb_load_fw_cfg_setting: APCF_ADD_MAC01: found & stored in 1 btmtk_usb_load_fw_cfg_setting: APCF_ADD_MAC_LOCATION00: found & stored in 0 btmtk_usb_load_fw_cfg_setting: APCF_ADD_MAC_LOCATION01: found & stored in 1 btmtk_usb_load_fw_cfg_setting: RADIOOFF00: found & stored in 0 btmtk_usb_load_fw_cfg_setting: WAKEUP_TYPE_WAVEFORM00: found & stored in 0 btmtk_usb_load_fw_cfg_setting: RADIOOFF_COMPLETE_EVENT00: found & stored in 0 File: misc/bluedroid/wake_on_ble.conf bt_env is NULL mmc change mount : cusdata ** File not found misc/bluedroid/wake_on_ble.conf [ERROR] vfs_getsize:449: ext4filesize mmc fail LD_load_code: Get file size fail mmc change mount : tvconfig ** File not found misc/bluedroid/wake_on_ble.conf [ERROR] vfs_getsize:449: ext4filesize mmc fail LD_load_code: Get file size fail ** Bad Signature on 0:48: expected 0x5840, got 0x0000 LD_load_code: vfs_mount vendor fail mmc change mount : userdata Failed to mount ext2 filesystem... ** Bad ext4 partition or disk - mmc 0:47 ** [ERROR] vfs_getsize:449: ext4filesize mmc fail LD_load_code: Get file size fail ** Bad Signature on 0:48: expected 0x5840, got 0x0000 LD_load_code: vfs_mount system fail ** Bad Signature on 0:48: expected 0x5840, got 0x0000 LD_load_code: vfs_mount APP fail btmtk_usb_load_woble_setting: There is no DEVICE RECORD for wake-up btmtk_usb_set_apcf: Set APCF filter from woble_setting.bin btmtk_usb_set_apcf: Send woble_setting_apcf[0] 57 FD 27 06 00 0A 46 00 00 79 35 8C 9D 16 A8 00 00 00 00 43 52 4B 54 4D FF FF 00 FF FF FF FF FF FF 00 00 00 00 FF FF FF FF FF usb_bt_interrupt_msg: epType = 0x2 usb_bt_interrupt_msg: ret = 0x0 btmtk_usb_set_apcf: Send woble_setting_apcf[1] 57 FD 0A 01 00 0A 20 00 20 00 01 80 00 usb_bt_interrupt_msg: epType = 0x2 usb_bt_interrupt_msg: ret = 0x0 btmtk_usb_set_unify_woble: Send radio off C9 FC 3C 01 20 02 00 01 02 01 00 02 40 0A 02 41 0F 05 24 20 04 32 00 09 26 C0 12 00 00 12 00 00 00 05 10 02 00 20 00 04 42 09 01 02 12 48 01 FF FF 00 00 10 00 00 FE 66 66 00 00 10 00 CC FE usb_bt_interrupt_msg: epType = 0x2 usb_bt_interrupt_msg: ret = 0x0 btmtk_usb_send_hci_cmd: got unknown event btmtk_usb_send_hci_cmd: try get event again usb_bt_interrupt_msg: epType = 0x2 usb_bt_interrupt_msg: ret = 0x0 Ldbtusb_SetWoble: usb set woble end do_setMtkBT: ready to do usb_stop do_setMtkBT: stop usb port: 2 mmc change mount : cusdata Loading file "bsp/chip/pm/PM.bin" at offset 0x0 from mmc device 0 partition cusdata 40959 bytes read Wait for PM51 standby...........PM51 run ok...........-usb_stop(USB_PORT0) -usb_stop(USB_PORT1) -usb_stop(USB_PORT2) -usb_stop(USB_PORT3) [MDrv_PM_Init_Key][909] Retry send MBX CMD(0x1) to PM51. [MDrv_PM_Init_Key][909] Retry send MBX CMD(0xB2) to PM51. LD_btmtk_usb_getWoBTW: LD_btmtk_usb_getWoBTW, u8WoBTW = 1 [MDrv_PM_Init_Key][909] Retry send MBX CMD(0xB4) to PM51. Set Power Off Short CRC Check OPEN: 1
Build at Oct 16 2023 - 16:31:28
WOW_GPIO_NUM = 0 WOW_GPIO_NUM is invalid WOBT_GPIO_NUM = 26 WOBT_PM_GPIO_NUM = 20 WOEWBS_GPIO_NUM = 255 WOEWBS_PM_GPIO_NUM = 255 BTW = 1 USB = FF VAD = FF 0x8709 яUART_115200
[Mboot] ===== sw IR Config Register ===== [Mboot] ===== Attach IR Interrupt ====== Uboot Relocation: 152 MiB
eMMC HS400 5.1 200MHz eMMC 29.12 GB eMMC used life: 0~10% CID 0x00B9524A 0xB6390452 0x3444544A 0x42000115 DRAM : 3072MB SAR5=ON In: serial Out: serial Err: serial Net: No ethernet found. MAC: 0x18: 0x84: 0xC1: 0x1D:0x5: 0xF5 [AT][MBoot][Driver Init][664] mmc change mount : tvconfig ** File not found model.info [ERROR] vfs_getsize:449: ext4filesize mmc fail No enough buffer or path fail(model.info) : [src/MsUtility.c] [loadscript] model.info not find !! Clean model_info env Writing to MMC(0)... 128 blocks written: OK 128 blocks written: OK done Try virtual ab bootloader_control... 0:MCP_S_D4_2666_16G_4x 1:EXT_D4_2666_8G_4x DRAM Channel 0 Size = [4096MB] Try virtual ab bootloader_control...
Changelist: 24543697 do not first setup(first_setup=1), skip self adaption. ============= set bootargs =============== Hit any key to stop autoboot: 0 enable dont overwrite function DC on !! mmc change mount : project_id Size of file "project_id.ini" from mmc device 0 partition project_id: 294 bytes Loading file "project_id.ini" at offset 0x0 from mmc device 0 partition project_id 294 bytes read [Mboot_IR] boot from dynamic ir Try virtual ab bootloader_control... ENV_UPGRADE_COMPLETE =0 ENV_UPGRADE_MODE =null androidboot boot reason =reboot Writing to MMC(0)... 128 blocks written: OK 128 blocks written: OK done [QHB] PowerOnMode = 241, u4BootCtrl = 0x0, fgStateOn = 1 [QHB] prepare to CLEAR QHB [QHB] not quiescent boot. DC on !! !!! [do_audiopreinit] Skip Power Music !!! Try virtual ab bootloader_control... MOD Output Channel Order not set!!!! [QHB] normal boot mode Active Standby Mode FALSE =====
MsDrv_PNL_Init:Bypass SetDivison LINK TYPE = EXT [Utopia][PNL]: [3866]read efuse bank 0x4D mask 4294967295 result 1937789566 [Utopia][PNL]: RCon Final Set=18 [Utopia][PNL]: [MHal_PNL_EfuseMPLL][10058]EfuseMPLL=1 mi OLED support = 0 [MApi_XC_MLG_GetStatus, 2911]No instance existed, please get an instance by calling MApi_XC_Init() first [XC,Version] EN_DEMURA_MULTI_NOT OK [ERROR] MApi_Demura_Init:313: multi_vendor input is not valid, init fail [Utopia][PNL]: Swing_Level in =350 [Utopia][PNL]: [_MHal_PNL_MOD_Swing_Refactor_AfterCAL]Swing value after refactor = 9 [panel_dinit, 811]Pre-Emphasis actvie [AT][MB][panel_pre_init][963] Try virtual ab bootloader_control... Wait for PM51 standby DRAM ...........PM51 run ok...........-usb_stop(USB_PORT0) -usb_stop(USB_PORT1) -usb_stop(USB_PORT2) -usb_stop(USB_PORT3)
###### Android Verify Boot 2.0 ######
[init_std] OPTEE version is 3 ubootRpmbReadRequest ubootRpmbVerifyReadResponse ubootRpmbReadRequest ubootRpmbVerifyReadResponse Try virtual ab bootloader_control...
[AT][MB][bootlogo begin][1315] [AT][MB][JPD Decode][1345] [showLogo] GOP Boot Logo Index 2 [AT][MB][Show Logo][1362] Boot state is: Green !
readKL_dtb load AB partition boot_b boot_b image header version: 2
emmc_load_dtbo load AB partition dtbo_b ## emmc_load_dtbo: Load dtbo image from partition: dtbo_b ## Load dtbo image done, image size: 2466 Byte ! [QHB] normal boot mode Active Standby Mode FALSE =====
---MsDrv_PNL_BackLigth_On:2406 Set MsDrv_PNL_BackLigth_On DelayTask 81 [QHB] normal boot mode Active Standby Mode FALSE ===== !!! [do_bootmusic] Skip Power Music !!! [AT][MBoot][Boot Nuttx][1620] Kernel command line: quiet dbg_mutex=0 no_autorun_log=1 loglevel=1 androidboot.boot_devices=mstar_mci.0 buildvariant=user ANDROID HEADER V2 Getting the dtb of index: 0 ... OK -usb_stop(USB_PORT0) -usb_stop(USB_PORT1) -usb_stop(USB_PORT2) -usb_stop(USB_PORT3) Loading Kernel Image ... OK Applying the overlay fdt of index: 0 ... OK Applying the overlay fdt of index: 2 ... OK ## boot_ufdt_overlay: Merge DTBO to main DTB done, takes 0.017 ms Loading Device Tree to 283CF000, end 283D9516 ... OK [AT][MB][start kr][1714]
Starting kernel ...
[ERROR] _get_new_map_format_from_env:531: get MI_KERNEL_POOL3_ADR fail [ERROR] _get_new_map_format_from_env:531: get MI_KERNEL_POOL4_ADR fail set 64 bit mode INFO: CPU0 Preparing for EL3 exit to normal world INFO: CPU0 Next image address = 0x20280000 INFO: CPU0 Next image spsr = 0x3c9 INFO: mstar_primary_kernel_enter 153 283daa00 23000000 24000000 b25de1 [ 0.000000] Function = void dma_contiguous_reserve(phys_addr_t), Line = 578, set pool_id: 30 as a FAKEMEM CMA HEAP [ 0.000000] [ 0.000000] Function = void memory_present(int, unsigned long, unsigned long), go handling FAKEMEM mem_section 0xE0000 to 0x100000, @ section 14 [ 0.000000] Function = void memory_present(int, unsigned long, unsigned long), go handling FAKEMEM mem_section 0xF0000 to 0x100000, @ section 15 [ 0.000000] Function = void free_area_init_core(struct pglist_data *), Line = 7196, origin init from 0x20200 to 0x98400 [ 0.000000] Function = void free_area_init_core(struct pglist_data *), Line = 7196, origin init from 0xA0000 to 0xDDB00 [ 0.000000] Function = void free_area_init_core(struct pglist_data *), Line = 7196, origin init from 0x0 to 0x0 [ 0.000000] [ 0.000000] [ 0.000000] Function = void free_area_init_core(struct pglist_data *), fakemem __init_single_pfn 0xE0000 to 0x100000 [RAMLOG] tee_entry_get_ramlog_config 349
[RAMLOG] Chip ID: d2 44 6c 0f c8 35 17 ec
_check_ramlog_binary Ramlog AUTHEN fail
[ 0.768084] ==RTC== MDrv_RTC_Init, 86 [ 8.945021] page:00000000d1665c9a (phy is 0x0000000042046000), count:2 mapcount:1 mapping:000000006e180f6f index:0xf5be9 [ 8.955903] flags: 0x8003e(referenced|uptodate|dirty|lru|active|swapbacked) [ 9.023865] page:00000000d1665c9a (phy is 0x0000000042046000), count:2 mapcount:1 mapping:000000006e180f6f index:0xf5be9 [ 9.034751] flags: 0x8003e(referenced|uptodate|dirty|lru|active|swapbacked) [ 9.060350] page:00000000d1665c9a (phy is 0x0000000042046000), count:2 mapcount:1 mapping:000000006e180f6f index:0xf5be9 [ 9.071231] flags: 0x8003e(referenced|uptodate|dirty|lru|active|swapbacked) [ 9.093109] page:00000000d1665c9a (phy is 0x0000000042046000), count:2 mapcount:1 mapping:000000006e180f6f index:0xf5be9 [ 9.103993] flags: 0x8003e(referenced|uptodate|dirty|lru|active|swapbacked) [ 9.162566] page:00000000d1665c9a (phy is 0x0000000042046000), count:2 mapcount:1 mapping:000000006e180f6f index:0xf5be9 [ 9.173447] flags: 0x8003e(referenced|uptodate|dirty|lru|active|swapbacked) [ 9.230680] page:00000000d1665c9a (phy is 0x0000000042046000), count:2 mapcount:1 mapping:000000006e180f6f index:0xf5be9 [ 9.241563] flags: 0x8003e(referenced|uptodate|dirty|lru|active|swapbacked) [ 9.265888] page:00000000d1665c9a (phy is 0x0000000042046000), count:2 mapcount:1 mapping:000000006e180f6f index:0xf5be9 [ 9.276768] flags: 0x8003e(referenced|uptodate|dirty|lru|active|swapbacked) console:/ $ Error! failed to finit_module failed to insmod ko kopath=/vendor/lib/modules/firmware_class.ko error(17):File exists Error! failed to finit_module failed to insmod ko kopath=/vendor/lib/modules/cfg80211.ko error(17):File exists get line is 0e8d:7663:/vendor/lib/modules/btmtk_usb.ko get line is 0e8d:7663:/vendor/lib/modules/mtprealloc_mt7663.ko get line is 0e8d:7663:/vendor/lib/modules/wlan_mt7663.ko get line is 0e8d:7668:/vendor/lib/modules/btmtk_usb.ko get line is 0e8d:7668:/vendor/lib/modules/mtprealloc_mt7668.ko get line is 0e8d:7668:/vendor/lib/modules/wlan_mt7668.ko get line is 0e8d:7961:/vendor/lib/modules/btmtk_usb_unify.ko get line is 0e8d:7961:/vendor/lib/modules/mtprealloc_mt7961.ko get line is 0e8d:7961:/vendor/lib/modules/wlan_mt7961.ko Bus 003 Device 001: ID 1d6b:0002 Bus 001 Device 001: ID 1d6b:0002 Bus 004 Device 001: ID 1d6b:0002 Bus 002 Device 001: ID 1d6b:0002 Bus 003 Device 002: ID 0e8d:7663 Good! we find wifi usb dongle,and then to insmod ko [RAMLOG] tee_get_ramlog_config 334
[RAMLOG] Chip ID: d2 44 6c 0f c8 35 17 ec
_is_ramlog_enable AUTHEN buffer is zero or len is not equal to 16
[ 12.458762] page:00000000d1665c9a (phy is 0x0000000042046000), count:2 mapcount:1 mapping:000000006e180f6f index:0xf5be9 [ 12.469646] flags: 0x8003e(referenced|uptodate|dirty|lru|active|swapbacked) success to insmod ko, vid=0e8d pid=7663 kopath=/vendor/lib/modules/btmtk_usb.ko Good! we find wifi usb dongle,and then to insmod ko success to insmod ko, vid=0e8d pid=7663 kopath=/vendor/lib/modules/mtprealloc_mt7663.ko Good! we find wifi usb dongle,and then to insmod ko success to insmod ko, vid=0e8d pid=7663 kopath=/vendor/lib/modules/wlan_mt7663.ko
netpriv: maxpriv size is 256 netpriv: device is wlan0 netpriv: get cmd number 35823 netpriv: cmd driver:0x00000000 run success 0x00000000 [wlan_dongle_detect]: mcr_ans is 0
end run cmd netpriv: maxpriv size is 256 netpriv: device is wlan0 netpriv: get cmd number 35823 netpriv: cmd driver:0x00076630 run success 0x00076630 [wlan_dongle_detect]: mcr_ans is 76630
end run cmd the mcr is : 7663[wlan_dongle_detect]:wifi dongle is mt7663 Init wrapper sys mutex successful. Pid:365 Init wrapper sys mutex successful. Pid:523 [ 23.894354] au32IRWakeHotkey[0] = 0xbf085 [ 23.898632] au32IRWakeHotkey[1] = 0xbf086 [ 23.902887] au32IRWakeHotkey[2] = 0xbf089 [ 23.907029] u1HotkeyCfgNum = 3
CPU_AUDIO is running!
--- Launch TV F/W --- /mnt/vendor/linux_rootfs/basic/3rd_ini/ginga_totvs/global_env_setup.ini Running rc.local... insmod: /basic/fusion.ko: No such file or directory Init wrapper sys mutex successful. Pid:581 MI_SYS_Init() without Parameter Init wrapper sys mutex successful. Pid:473 Info: get MI daemon priority before System Init: [-20] !!!Enter MI daemon prcoess!! start time =27211 !!!Enter MI daemon flow time=27221!! HASHKEY_Verify=(0)(0) MI_SYS_Init() with Parameter [Utopia][MSOS]: [ERROR][MsOS_CreateMutex][2328] [MsOS_CreateMutex][2328] Update max number of msos mutex: 256 [utopia info] open: /vendor/etc/utopia.conf [Utopia][MSOS]: [WARN][MsOS_Init][5952] Already inited. SYS_Init ioctl UTOPIA_IOCTL_GetChipID OK. SYS_Init(322)(16515073)(252)(0)(1)
KeyCustomerList[1].chipid:e8 >> Start MM service >> Start INJPLAY service >> Start SUBTITLE service >> Start TTX service >> Start VOC service Open MI_OSD kernel module successful MI_DISP_GetHandle[665]: Error 0x3: failed to ioctl(MI_DEV_IOC_DISP_GET_HANDLE) MI_WRAPPER_RegisterCallback[761]: listen event(fffffff0) failed! _MI_WRAPPER_DISP_RegisterCallback[2345]: Error 0x1: failed to ioctl(MI_DEV_IOC_DISP_REGISTER_CALLBACK) HDCP callback is already registered! MI_WRAPPER_RegisterCallback[761]: listen event(fffffff1) failed! _MI_WRAPPER_DISP_RegisterCallback[2345]: Error 0x3: failed to ioctl(MI_DEV_IOC_DISP_REGISTER_CALLBACK) HDCP callback is already registered! SYS User inited:0 MI_IIC_Init[168]: Error 0x2: failed to ioctl(MI_DEV_IOC_IIC_INIT) _s32MikAextinFd: 39, aextin init result : 0 [Utopia][MSOS]: [ERROR][MsOS_CreateMutex][2328] [MsOS_CreateMutex][2328] Update max number of msos mutex: 256 [utopia info] open: /vendor/etc/utopia.conf [Utopia][MSOS]: [WARN][MsOS_Init][5952] Already inited. SYS_Init ioctl UTOPIA_IOCTL_GetChipID OK. SYS_Init(322)(16515073)(252)(0)(1) _MI_WRAPPER_SYS_SecurityAuthentication[769]: Invalid parameter! _MI_WRAPPER_SYS_SecurityAuthentication[769]: pstInitParams is NULL. MI_IIC_Init[168]: Error 0x2: failed to ioctl(MI_DEV_IOC_IIC_INIT) _s32MikAextinFd: 30, aextin init result : 2 Open MI_OSD kernel module successful [cpuAudio_createDecoderMonitorThread][314]armAudio_decoderMonitor_ver: 0x1f thread created successfully cpuAudio getThreadInfo... [Main]open ok !!!MI daemon prcoess start! MI daemon cost time=944!!! Info: get MI daemon priority after Module Init: [0] cpuAudio[Info](thread-name:cpu_audio)(pid:581)(tid:769) cpuAudio[Version](821,0x1F) [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [SIG_TRACER]:init ok [ 31.462017] [GLUE] watchdog thread start. [ 35.945653] [MI_CEC_SetAttr][2834] Set CEC eARC mode : 3 [ 37.073631] [MI_CEC_SetAttr][2834] Set CEC eARC mode : 3 [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler! open /dev/snd/pcmC2D0c in NON-Block mode open /dev/snd/pcmC2D0c in NON-Block mode [MI_VOC] - MI_VOC_GetHandle()[3472]: Can't find handler!
Файлы
Прошивки
Продажа
Литература
Статьи
Для просмотра сообщения Вы должны быть Участником форума. Для этого Вам необходимо 
Зарегистрировано всего