Boot-
DRAM Channel A Calibration.
HW Byte 0 : DQS(9 ~ 34), Size 26, Set 21, HW_Set 24.
HW Byte 1 : DQS(6 ~ 31), Size 26, Set 18, HW_Set 20.
HW Byte 2 : DQS(8 ~ 37), Size 30, Set 22, HW_Set 24.
HW Byte 3 : DQS(9 ~ 33), Size 25, Set 21, HW_Set 24.
,rDQS CHA offset -0x03030203 .
DRAM A Size = 1024 Mbytes.
DRAM Channel B Calibration.
HW Byte 4 : DQS(9 ~ 40), Size 32, Set 24, HW_Set 26.
HW Byte 5 : DQS(6 ~ 32), Size 27, Set 19, HW_Set 21.
,rDQS CHB offset -0x00000004 .
DRAM B Size = 128 Mbytes.
Boot
Start Pmain
0x0000a000
EMMC boot

CID:0x960811d3
:0x0403022a
:0x34473164
:0x90014a48
LZHS addr:0x00100040
LZHS size:0x0007de28
LZHS checksum:0x00000032
Boot
Start Lmain

MT5398 Boot Loader v0.9
SIF_Master0: new design

[ITM]====send value start!!=====U▒U
[ITM]Time out:50 ms ===>break now!

[ITM]===no ITM start command received,clear kernel flag now!!===]

[ITM]===no ITM start command received,clear kernel flag done!!===]
Boot reason: A/C power on!!
[PDWNC] PDWNC_PHILIPS_ReadWakeupReason: 6 (status 0x0)
[EDID Info] Update EDID from NVM to SRAM...mode : 1
read from eeprom ioff 0 phy_off 2920

Load VGA internal EDID.................
Load HDMI internal EDID (SRAM).................
EDID Table:.................
0 ff ff ff ff ff ff 0
41 c 4 3 1 1 1 1
1 18 1 3 80 80 48 78
a e6 92 a3 54 4a 99 26
f 4a 4c 21 8 0 b3 0
95 0 a9 40 90 40 81 0
81 80 81 40 1 1 2 3a
80 18 71 38 2d 40 58 2c
45 0 0 d0 52 0 0 1e
2 3a 80 d0 72 38 2d 40
10 2c 45 80 0 d0 52 0
0 1e 0 0 0 fc 0 50
68 69 6c 69 70 73 20 46
54 56 a 20 0 0 0 fd
0 30 3e f 46 1e 0 a
20 20 20 20 20 20 1 ac
2 3 39 f1 52 10 1f 20
22 21 5 14 4 13 12 3
11 2 16 7 15 6 1 26
9 1f 7 15 7 50 83 1
0 0 73 3 c 0 10 0
38 3c a0 4c 4c c8 64 1
2 3 1 40 1 ff e2 0
49 1 1d 80 3e 73 38 2d
40 7e 2c 45 80 0 d0 52
0 0 1e 1 1d 80 d0 72
1c 16 20 10 2c 25 80 0
d0 52 0 0 9e 1 1d 0
bc 52 d0 1e 20 b8 28 55
40 0 d0 52 0 0 1e 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 d6
CEC Physical offset 166
HDMI1 Physical adr 0x10
HDMI1 PA 0x10
HDMI1 checksum 0xd6
HDMI2 PA 0x20
HDMI2 checksum 0xc6
HDMI3 PA 0x30
HDMI3 checksum 0xb6
HDMI4 PA 0x40
HDMI4 checksum 0xa6
[EDID Info] Update EDID Finish...
Init WiFi and RF4CE
IR DATA register : 0x 0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x d516b8, size: 24576)success!!
T8032 FW version: 9
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x4e080 0x80
(SDR)Request Clk:24MHz Bus Clk:24MHz, SelVal:7

[ITM]====send value start!!=====U▒U
[ITM]====checked already, continue boot!======
1st MAC in EEP is valid (1c:5a:6b:64:cd:ae)
1st : (1c:5a:6b:64:cd:ae)
2nd : (1c:5a:6b:64:cd:ae)
[PDWNC] Current state : 0x1
[PDWNC]PDWNC_PHILIPS_DetermineNextState : u4Event = 0x6
PDWNC_PHILIPS_DetermineNextState : u4Current = 1
PDWNC_PHILIPS_DetermineNextState : system booting
PDWNC_PHILIPS_DetermineNextState : event = PDWNC_WAKE_UP_REASON_AC_POWER
PDWNC_PHILIPS_DetermineNextState : Lounge mode = 0
Current = 0x1, Event = 0x6, Next = 0x1
[PDWNC] PDWNC_PHILIPS_EnterNextState : u4Next = 0x1
[PDWNC]PDWNC_ReadWakeupReason = 0x6
[PDWNC]Enter normal mode, LED changes to normal
[PDWNC] set splash on pin 204 as high
PDWNC_Init
[Knight]SetWorkMarkBrightness:type:4, mode=0, level:3(duty cycle:100)
vApiPanelPowerSequence: Set to General PWM:1
USB0: Set GPIO51 = 1.
USB1: Set GPIO43 = 1.
USB2: Set GPIO44 = 1.
LDR_PostInit
GPIO 202 output mode set as 0

Do USB upgrade
USB: Vbus turn up time = 581 ms, Max =300 ms.
USB-2: insert.
USB-2: ClassCode= 0x9, u4Diff=0 ms.

FIND_CLASS_HUB.
u4timeStamp=1:683476, 886 , F:mu_hcore.c