System startup

version:U-Boot 2018.07 (Dec 02 2020 - 15:51:09 +0800)

TLB ADDR:0xe000000
Build Date: Dec 2 2020, 15:52:49
CPU: Hi3751v350
Boot Media: eMMC

gd:10bfff50,DRAM addr:0x0,size:0x40000000
1 GiB
WARNING: Caches not enabled
board_init,41
MMC: hisi-sdhci: 0

EMMC/MMC/SD controller initialization.
current clock: 400000Hz, host timing: 0x0
current clock: 52000000Hz, host timing: 0x1
current clock: 120000000Hz, host timing: 0xa
MMC/SD Card:
MID: 0x15
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "8GTF4"
Chip Type: MMC
Version: 5.1
Speed: 120000000Hz
Bus Width: 8bit
Mode: HS400ES
Loading Environment from MMC... OK
Net:

======== [PARAM] ========
SYSID: 0x19060350
SUSPENDTYPE: shutdown
GPIO GROUP 0x0 disable
GPIO GROUP 0x1 disable
GPIO GROUP 0x2 disable
GPIO GROUP 0x3 disable
GPIO GROUP 0x4 disable
TIMER WAKEUP: 0xffffffff
IR NUM: 0x6
IR KEY: 0xed12bf40
IR KEY: 0xed126180
IR KEY: 0xffffff
IR KEY: 0xfe019088
IR KEY: 0xe41b9088
IR KEY: 0xf00f9088
LSADC ZERO: 0xff
LSADC channel A enable
LSADC channel B enable
LSADC channel C disable
LSADC channel D disable
LSADC GLITCHSAMPLE: 0x5
LSADC TIMESCAN: 0x258
LSADC POWERKEY0: 0x0, 0x14
LSADC POWERKEY1: 0xff, 0xff
LSADC POWERKEY2: 0xff, 0xff
LSADC POWERKEY3: 0xff, 0xff
auto wakeup flag: 0x0
wakeup condition: 0x777
power down delay: 0x4b0
power up delay: 0x14
Cvt_Pm_State_Init uart-mode val[0] = 0x0
light off
CEC ONE Play: 0x0
HDMIRX_CLK_WKUP: 0x0
HDMIRX HPD invert: 0xf
HDMIRX HPD function: 0x1
HDMIRX bCecWkup: 0x1
HDMIRX enSuspendPort: 0x5000001
i2c pull up disable
lsadc:6bit,data_delta=8,enable deglitch,power down,continue scan
VGA Wakeup is off!
====== [MCU init ready] ======
power down ARM ===>
ddr_power_ctrl:50201
group 2,bit 5 have no pinmux
====== [ARM power down] ======
stb gpio states:
group dir(0:in 1:out) level(0:low 1:high) func(0:other 1:gpio)
0 00000010 00000000 00000000
1 00000000 00000000 00000010
2 00100000 10000000 00000000
3 00000000 00000000 00000000
4 00000000 00000000 00000000
====== [PM File: ID_PM_CVTE_DEFAULT_EU.txt ] ======
====== [version : 050 - v3.0] ======
===== [waiting for powerkey] =====
DDC_Pinmux_config to uart mode!

_lsadc channel A: 0x93001000

_power on!
====== [wake up by keypad] ======
i2c pull up enable
suspend last 47s
====== [ARM power on] ======

System startup

version:U-Boot 2018.07 (Dec 02 2020 - 15:51:09 +0800)

TLB ADDR:0xe000000
Build Date: Dec 2 2020, 15:52:49
CPU: Hi3751v350
Boot Media: eMMC

gd:10bfff50,DRAM addr:0x0,size:0x40000000
1 GiB
WARNING: Caches not enabled
board_init,41
MMC: hisi-sdhci: 0

EMMC/MMC/SD controller initialization.
current clock: 400000Hz, host timing: 0x0
current clock: 52000000Hz, host timing: 0x1
current clock: 120000000Hz, host timing: 0xa
MMC/SD Card:
MID: 0x15
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name: "8GTF4"
Chip Type: MMC
Version: 5.1
Speed: 120000000Hz
Bus Width: 8bit
Mode: HS400ES
Loading Environment from MMC... OK
Net:

Slave boot startup

version:U-Boot 2018.07 (Dec 02 2020 - 15:51:44 +0800)

TLB ADDR:0x10e00000
Build Date: Dec 2 2020, 15:53:19
CPU: Hi3751v350
Boot Media: eMMC

gd:13ffff50,DRAM addr:0x0,size:0x40000000
1 GiB
WARNING: Caches not enabled
board_init,41

The DDR memory layout:
page table: 0x10e00000 - 0x11200000 4 MiB
stack: 0x11200000 - 0x11600000 4 MiB
irq stack: 0x11eefecc - 0x11fefecc 1 MiB
.text: 0x14000000 - 0x14069a5c 422.6 KiB
data: 0x14069a5c - 0x160f9d50 32.6 MiB
init_sequence_r done!
Not enough memory for reserve memory!
cant has HI_DRV_MAILBOX_CVTE_UPGRADE_INFO
Loading Environment from MAILBOX... OK
[addr1 addr2 addr3 [addr4]
- start atf at addr1
Image at addr2,fdt at addr3
optional secureos at addr4

NOTICE: BL31: v2.0(release):HISI350_fae_eu_v1.10.0.3-dirty
NOTICE: BL31: Built : 16:28:30, Dec 2 2020
Uncompressing Linux... done, booting the kernel.