Здравствуйте уважаемые форумчане нужна ваша помощь! PHILIPS 55PFS8159/60 QV14.1 SSB 715RLPCB0000000055 EMMC H26M31003GMR Первым делом снял лог загрузки (его выложу ниже) сразу скажу в логах я не силён но изучаю в нём смутило две вещи одна указывает TZ CPU2 ERROR и не может найти файл 'flash_recovery' кстати в рекавери пробивал входить не входил из начально.Дабы сузить круг считал родную emmc по isp считалось без нареканий,взял новую такую-же emmc и записал всё родное обратно с конфигурацией как положено.Поставил на место всё точно также (лог загрузки с новой emmc приложу) по логу по мне ни чего не изменилось. Прошу помочь разобраться или проц сдох или всё-же родной дамп битый,может кто-то поможет проверить буты! Пробивал user раздел записать другим дампом взятый вот здесь на форуме но он был снят UFPI и boot1 boot2 размерами меньше переделывал название файлов чтобы записать своим ENTT оно вроде записалось но указывал прогер на адреса. Если всё же дело в дампе может кто поделится 100% рабочим дампом считанный ENTT дабы проверить и собрать свой с ключами дамп если они ещё живы. Ах да с не родным user разделом тв после логотипа PHILIPS показал на экране быстро артефакты и после тишина! Буду рад любой помощи свой родной дамп могу скинуть чуть позже.
Добавлено (15.10.2021, 01:32:07) --------------------------------------------- ЭТО ЛОГ С РОДНОЙ EMMC [ 0] sys_init start. boot_strap=0x00000514 (source=eMMC), boot_state=0x0 [ 278] image verified, start at 0x00920000... tz kernel starting... MV88DE3114(BG2Q)-A1 total 4 cpus, v2.0.0.21, Aug 5 2014 14:39:52 0231[ 333] start_bootloader U▒ULAUNCH_ITM is set to zero board_number = 6 uiBoot = 0
I2C switch set as 0
I2C switch set as 1 --------- I2C Initialization ---------- I2C_INIT: I2C-2 bus I2C_INIT: I2C-1 bus I2C_INIT: I2C-0 bus DDR reg 0xF7CB0BAC value : 0x00021421 DDR reg 0xF7CB0C00 value : 0x00004031 leakage info 320. cpu from 1200 to 1300 set vcpu to 1225mv set vcpu to 1250mv set vcpu to 1275mv set vcpu to 1300mv set Vcpu to 1300 mv. core from 1200 to 1150 set Vcore to 1175mv set Vcore to 1150mv set Vcore to 1150 mv. flash_ts_init() success.
I2C switch set as 1 --------- I2C Initialization ---------- I2C_INIT: I2C-2 bus I2C_INIT: I2C-1 bus I2C_INIT: I2C-0 bus DDR reg 0xF7CB0BAC value : 0x00021421 DDR reg 0xF7CB0C00 value : 0x00004031 leakage info 320. set Vcpu to 1300mV, default setting by hardware. core from 1200 to 1150 set Vcore to 1175mv set Vcore to 1150mv set Vcore to 1150 mv. flash_ts_init() success.
GSM 0xf7fcd040 0x009c0261; 0xf7ea0014: 00000072 00240611 00000253 1249008a 0xf7ea0028: 01249492 00000048 1ca54009 0430e44d 0xf7ea003c: 00000000 00000000 0000001f 63c06a52 Clock configuration: VCO_B frequency 1620 AVPLLB[4] frequency 300 AVPLLB[5] frequency 800 AVPLLB[6] frequency 1680 AVPLLB[7] frequency 610 cpuPll frequency 1200 memPll frequency 1500 sysPll frequency 800 dClk frequency 375 cpuClk frequency 1200 sysClk frequency 400 drmClk frequency 400 cfgClk frequency 100 gfxClk frequency 400 zspClk frequency 400 perifClk frequency 200 pCubeClk frequency 610 vScopeClk frequency 610 nfcEccClk frequency 100 vppSysClk frequency 400 appClk frequency 800 gfx3DCoreClk frequency 420 gfx3DSysClk frequency 400 arcRefClk frequency 400 vipClk frequency 400 sdioXinClk frequency 200 sdio1XinClk frequency 200 gfx3DShClk frequency 420 avif0Clk frequency 300 avif1Clk frequency 300 [00,sd00] bootloader: part1(start=0, blks=1, version=201710271804), part2(start=0, blks=1, version=000000000000) [01,sd01] fts: part1(start=32, blks=32, version=201710271804), part2(start=32, blks=32, version=000000000000) [02,sd02] recovery: part1(start=64, blks=120, version=201710271804), part2(start=64, blks=120, version=000000000000) [03,sd03] tzk_recovery: part1(start=184, blks=8, version=201710271804), part2(start=184, blks=8, version=000000000000) [04,sd04] factory_setting: part1(start=192, blks=128, version=201710271804), part2(start=192, blks=128, version=000000000000) [05,sd05] itm: part1(start=320, blks=128, version=201710271804), part2(start=320, blks=128, version=000000000000) [06,sd06] boot: part1(start=448, blks=24, version=201710271804), part2(start=448, blks=24, version=000000000000) [07,sd07] tzk_normal: part1(start=472, blks=8, version=201710271804), part2(start=472, blks=8, version=000000000000) [08,sd08] system: part1(start=480, blks=1600, version=201710271804), part2(start=480, blks=1600, version=000000000000) [09,sd09] user_setting: part1(start=2080, blks=960, version=201710271804), part2(start=2080, blks=960, version=000000000000) [10,sd10] cache: part1(start=3040, blks=896, version=201710271804), part2(start=3040, blks=896, version=000000000000) [11,sd11] firmware: part1(start=3936, blks=64, version=201710271804), part2(start=3936, blks=64, version=000000000000) [12,sd12] factory_data: part1(start=4000, blks=32, version=201710271804), part2(start=4000, blks=32, version=000000000000) [13,sd13] userdata: part1(start=4032, blks=3328, version=201710271804), part2(start=4032, blks=3328, version=000000000000) get macaddr from fts: 1c:5a:6b:75:0a:1f macaddr=1c:5a:6b:75:0a:1f get_reset_msg,1262: sysreset, need to get reset_msg_extra_size=0 tzk boot with normal mode by default start to kick off SM CPU: start 0x3ff0449c, size 63216 SM CPU is kicked[ of f . L1a]stIp(oSMwe):rm eondet eir s manoitn St[a n d by f ts6:] Wc(rSaM)sh: coEnutnteerri.nagn addrcoi_di:n i2t . [t s : b o o t1l2o]Wad(SerM).c:o mLmeaanvid:n g adc_init. [ 18]W(SM): PWM Initialized [ 21]I(SM): begin to run tasks [ 514]W(SM): Joystick connected verify boot image passed. OTP Temperature: 0 celsius degree Chip Version: 0xa1d Send bootmode=0 to SM. get macaddr from fts: 1c:5a:6b:75:0a:1f macaddr=1c:5a:6b:75:0a:1f Generated bootargs: androidboot.hardware=AND1E quiet lpj=11935744 root=/dev/ram0 androidboot.console=ttyS0 console=ttyS0,115200 init=/init vmalloc=448M quiet macaddr=1c:5a:6b:75:0a:1f emmc_ts.dev_id=1 emmc_ts.size=16777216 emmc_ts.erasesize=524288 emmc_ts.writesize=512 update system memory region: (0x01000000, 0x3f800000)->(0x40000000, 0x00800000) update system memory region(TZ): (0x40000000, 0x00800000)->(0x40000000, 0x40000000) ion_pool_num : 0x00000004, ion-attributes-num-per-pool : 0x00000002 pool[0]: name: SW_noncache, base =0x02800000 , size = 0x00800000 ion_attr[0]: 0x00000002 ion_attr[1]: 0x00000939 pool[1]: name: SW_other, base =0x03000000 , size = 0x16c00000 ion_attr[0]: 0x00000002 ion_attr[1]: 0x00000f3d pool[2]: name: NW_all, base =0x19c00000 , size = 0x22300000 ion_attr[0]: 0x00000002 ion_attr[1]: 0x00000f36 pool[3]: name: NW_noncache, base =0x3bf00000 , size = 0x02000000 ion_attr[0]: 0x00000002 ion_attr[1]: 0x00000f3a Responding to SM... Boot from system reset. don't do dts customization for A1D [ 2103] Boot normal GTV image Start kernel at 0x40008000 Uncompressing Linux... done, booting the kernel. [ 0.170477] CPU1: Unknown IPI message 0x1 [ 0.210430] CPU2: Unknown IPI message 0x1 [ 0.250417] CPU3: Unknown IPI message 0x1 [ 0.279622] gpio-regulator gpio-regulator.6: No 'states' property found [ 0.351692] marvell_tpv tpv.7: can't get vpuc regulator. [ 0.360613] berlin-ehci f7ed0000.usb: no pwr-gpio set [ 0.413741] berlin-ehci f7ee0000.usb: no pwr-gpio set [ 0.463611] berlin-ehci f7a30000.usb: no pwr-gpio set [ 0.538653] init: /init.googletv.rc: 44: ignored duplicate definition of service 'resourcemanager' [ 0.548306] init: /init.berlin.rc: 255: ignored duplicate definition of service 'ampaudioloopback' TEEC_RegisterTA result = 0x00000000 [ 1.089634] tpvfsck: Checking partition /dev/block/mmcblk0p9 [ 1.095512] tpvfsck: -p /dev/block/mmcblk0p9 [ 1.900806] tpvfsck: Check /dev/block/mmcblk0p9 ok, status 0 [ 1.906682] tpvfsck: Partition /dev/block/mmcblk0p9 fs check done [ 1.998291] tpvfsck: Checking partition /dev/block/mmcblk0p13 [ 2.004260] tpvfsck: -p /dev/block/mmcblk0p13 [ 2.027114] device-mapper: verity: data block 145855 is corrupted [ 2.429494] tpvfsck: Check /dev/block/mmcblk0p13 ok, status 0 [ 2.435468] tpvfsck: Partition /dev/block/mmcblk0p13 fs check done [ 2.450158] tpvfsck: Checking partition /dev/block/mmcblk0p10 [ 2.456144] tpvfsck: -p /dev/block/mmcblk0p10 [ 2.502094] tpvfsck: Check /dev/block/mmcblk0p10 ok, status 0 [ 2.508445] tpvfsck: Partition /dev/block/mmcblk0p10 fs check done [ 2.564474] fusion: unable to register major 250. Registered 247 instead [ 2.575699] VID/PID = 1286/2043, Boot2 version = 4000 [ 2.716294] device-mapper: verity: data block 145772 is corrupted s 2.769260] device-mapper: verity: data blo[c.k35 151 51 C4U3 is ORcoArrrump_ted er:233] verify_image fail (err=-13) [4.842284] TZ CPU3 ERROR[TAMgr_CreateInstance:66] can't find TA 53991704-facb-abcd-bffbc8d67fbf8891 [ 2.791039] leakage: 320 MV_OPENCRYPTO_DeviceKey_Initialize, line: 299, otp_status = 0xff MV_OPENCRYPTO_DeviceKey_Initialize, line: 301, tmp_test = 0xc rkek be selected BindInfo: 00000000 00000000 00000000 00000000 535b8b57 0d5a2f94 00000000 48000000 3bffefea 00001468 000000ff ca7a6b01 d689b19d 078040e2 [ 3.544789] vmeta user count:0, set voltage 1150000:1150000 [ 3.617132] FW is downloaded [ 4.142312] usb_reset_device() successful. [ 4.264542] init: cannot find '/system/bin/rild', disabling 'ril-daemon' [ 4.272352] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' [ 4.282269] init: cannot find '/system/bin/suspend_utils', disabling 'suspend_utils' [ 4.486165] device-mapper: verity: data block 115493 is corrupted [ 6088]W(SM): msg with invalid func-id 90 or start/end byte has been discarded [ 6328]W(SM): Initialising LED intensity values from TV settings database [ 6336]W(SM): Wake reason 0x0 [ 6751]W(SM): WM == 2 [ 5.648205] device-mapper: verity: data block 115095 is corrupted [ 7189]I(SM): #########wdt1 enable [ 6.426957] BT: Loading driver [ 6.430322] Marvell Bluetooth USB driver [ 6.434440] bt_usb_probe: intf bdd4a400 id 7f0eddf0 [ 6.439346] VID/PID = 1286/2044, Boot2 version = 3201 [ 6.453193] FW is Active [ 6.463768] BT: Create /dev/mbtchar0 [ 6.523012] BT: Create /dev/mfmchar0 [ 6.586281] BT: Driver loaded successfully
Добавлено (15.10.2021, 01:36:21) --------------------------------------------- Это с новой EMMC
[ 0] sys_init start. boot_strap=0x00000514 (source=eMMC), boot_state=0x0 [ 270] image verified, start at 0x00920000... tz kernel starting... MV88DE3114(BG2Q)-A1 total 4 cpus, v2.0.0.21, Aug 5 2014 14:39:52 0312[ 325] start_bootloader U▒ULAUNCH_ITM is set to zero board_number = 6 uiBoot = 0
I2C switch set as 0
I2C switch set as 1 --------- I2C Initialization ---------- I2C_INIT: I2C-2 bus I2C_INIT: I2C-1 bus I2C_INIT: I2C-0 bus DDR reg 0xF7CB0BAC value : 0x00021421 DDR reg 0xF7CB0C00 value : 0x00004031 leakage info 320. cpu from 1200 to 1300 set vcpu to 1225mv set vcpu to 1250mv set vcpu to 1275mv set vcpu to 1300mv set Vcpu to 1300 mv. core from 1200 to 1150 set Vcore to 1175mv set Vcore to 1150mv set Vcore to 1150 mv. flash_ts_init() success.
GSM 0xf7fcd040 0x009c0261; 0xf7ea0014: 00000072 00240611 00000253 1249008a 0xf7ea0028: 01249492 00000048 1ca54009 0430e44d 0xf7ea003c: 00000000 00000000 0000001f 63c06a52 Clock configuration: VCO_B frequency 1620 AVPLLB[4] frequency 300 AVPLLB[5] frequency 800 AVPLLB[6] frequency 1680 AVPLLB[7] frequency 610 cpuPll frequency 1200 memPll frequency 1500 sysPll frequency 800 dClk frequency 375 cpuClk frequency 1200 sysClk frequency 400 drmClk frequency 400 cfgClk frequency 100 gfxClk frequency 400 zspClk frequency 400 perifClk frequency 200 pCubeClk frequency 610 vScopeClk frequency 610 nfcEccClk frequency 100 vppSysClk frequency 400 appClk frequency 800 gfx3DCoreClk frequency 420 gfx3DSysClk frequency 400 arcRefClk frequency 400 vipClk frequency 400 sdioXinClk frequency 200 sdio1XinClk frequency 200 gfx3DShClk frequency 420 avif0Clk frequency 300 avif1Clk frequency 300 [00,sd00] bootloader: part1(start=0, blks=1, version=201710271804), part2(start=0, blks=1, version=000000000000) [01,sd01] fts: part1(start=32, blks=32, version=201710271804), part2(start=32, blks=32, version=000000000000) [02,sd02] recovery: part1(start=64, blks=120, version=201710271804), part2(start=64, blks=120, version=000000000000) [03,sd03] tzk_recovery: part1(start=184, blks=8, version=201710271804), part2(start=184, blks=8, version=000000000000) [04,sd04] factory_setting: part1(start=192, blks=128, version=201710271804), part2(start=192, blks=128, version=000000000000) [05,sd05] itm: part1(start=320, blks=128, version=201710271804), part2(start=320, blks=128, version=000000000000) [06,sd06] boot: part1(start=448, blks=24, version=201710271804), part2(start=448, blks=24, version=000000000000) [07,sd07] tzk_normal: part1(start=472, blks=8, version=201710271804), part2(start=472, blks=8, version=000000000000) [08,sd08] system: part1(start=480, blks=1600, version=201710271804), part2(start=480, blks=1600, version=000000000000) [09,sd09] user_setting: part1(start=2080, blks=960, version=201710271804), part2(start=2080, blks=960, version=000000000000) [10,sd10] cache: part1(start=3040, blks=896, version=201710271804), part2(start=3040, blks=896, version=000000000000) [11,sd11] firmware: part1(start=3936, blks=64, version=201710271804), part2(start=3936, blks=64, version=000000000000) [12,sd12] factory_data: part1(start=4000, blks=32, version=201710271804), part2(start=4000, blks=32, version=000000000000) [13,sd13] userdata: part1(start=4032, blks=3328, version=201710271804), part2(start=4032, blks=3328, version=000000000000) get macaddr from fts: 1c:5a:6b:75:0a:1f macaddr=1c:5a:6b:75:0a:1f tzk boot with normal mode by default start to kick off SM CPU: start 0x3ff0449c, size 63216 SM CPU is kicked [o f f . La1]sIt(pSowMe)r:m oedntee ris mnaiotn [t an d b y f ts6:] W(cSrMas)h:c Eonutnteerri.nagn adrdcoi_idn: i3t . f[t s : b o o t1l2o]Wad(SerM).c:o mLemaavnid:n g dc_init. a [ 18]W(SM): PWM Initialized [ 21]I(SM): begin to run tasks [ 514]W(SM): Joystick connected verify boot image passed. OTP Temperature: 0 celsius degree Chip Version: 0xa1d Send bootmode=0 to SM. get macaddr from fts: 1c:5a:6b:75:0a:1f macaddr=1c:5a:6b:75:0a:1f Generated bootargs: androidboot.hardware=AND1E quiet lpj=11935744 root=/dev/ram0 androidboot.console=ttyS0 console=ttyS0,115200 init=/init vmalloc=448M quiet macaddr=1c:5a:6b:75:0a:1f emmc_ts.dev_id=1 emmc_ts.size=16777216 emmc_ts.erasesize=524288 emmc_ts.writesize=512 update system memory region: (0x01000000, 0x3f800000)->(0x40000000, 0x00800000) update system memory region(TZ): (0x40000000, 0x00800000)->(0x40000000, 0x40000000) ion_pool_num : 0x00000004, ion-attributes-num-per-pool : 0x00000002 pool[0]: name: SW_noncache, base =0x02800000 , size = 0x00800000 ion_attr[0]: 0x00000002 ion_attr[1]: 0x00000939 pool[1]: name: SW_other, base =0x03000000 , size = 0x16c00000 ion_attr[0]: 0x00000002 ion_attr[1]: 0x00000f3d pool[2]: name: NW_all, base =0x19c00000 , size = 0x22300000 ion_attr[0]: 0x00000002 ion_attr[1]: 0x00000f36 pool[3]: name: NW_noncache, base =0x3bf00000 , size = 0x02000000 ion_attr[0]: 0x00000002 ion_attr[1]: 0x00000f3a Responding to SM... don't do dts customization for A1D [ 2090] Boot normal GTV image Start kernel at 0x40008000 Uncompressing Linux... done, booting the kernel. [ 0.170486] CPU1: Unknown IPI message 0x1 [ 0.210430] CPU2: Unknown IPI message 0x1 [ 0.250417] CPU3: Unknown IPI message 0x1 [ 0.279621] gpio-regulator gpio-regulator.6: No 'states' property found [ 0.351716] marvell_tpv tpv.7: can't get vpuc regulator. [ 0.360583] berlin-ehci f7ed0000.usb: no pwr-gpio set [ 0.413801] berlin-ehci f7ee0000.usb: no pwr-gpio set [ 0.463614] berlin-ehci f7a30000.usb: no pwr-gpio set [ 0.538716] init: /init.googletv.rc: 44: ignored duplicate definition of service 'resourcemanager' [ 0.548373] init: /init.berlin.rc: 255: ignored duplicate definition of service 'ampaudioloopback' TEEC_RegisterTA result = 0x00000000 [ 0.961507] tpvfsck: Checking partition /dev/block/mmcblk0p9 [ 0.967410] tpvfsck: -p /dev/block/mmcblk0p9 [ 1.066465] tpvfsck: Check /dev/block/mmcblk0p9 ok, status 0 [ 1.072332] tpvfsck: Partition /dev/block/mmcblk0p9 fs check done [ 1.089146] tpvfsck: Checking partition /dev/block/mmcblk0p13 [ 1.095179] tpvfsck: -p /dev/block/mmcblk0p13 [ 1.152385] device-mapper: verity: data block 145836 is corrupted [ 1.160670] device-mapper: verity: data block 145855 is corrupted [ 1.235958] tpvfsck: Check /dev/block/mmcblk0p13 ok, status 0 [ 1.241899] tpvfsck: Partition /dev/block/mmcblk0p13 fs check done [ 1.256186] tpvfsck: Checking partition /dev/block/mmcblk0p10 [ 1.262124] tpvfsck: -p /dev/block/mmcblk0p10 [ 1.294743] tpvfsck: Check /dev/block/mmcblk0p10 ok, status 0 [ 1.300683] tpvfsck: Partition /dev/block/mmcblk0p10 fs check done [ 1.341883] fusion: unable to register major 250. Registered 247 instead [ 1.352943] VID/PID = 1286/2043, Boot2 version = 4000 [ 1.444548] device-mapper: verity: data block 145772 is corrupted [ 1.460153] device-mapper: verity: data block 115143 is corrupted [ 2.389127] FW is downloaded [ 2.890295] usb_reset_device() successful. [ 3.012642] init: cannot find '/system/bin/rild', disabling 'ril-daemon' [ 3.020466] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' [ 3.030362] init: cannot find '/system/bin/suspend_utils', disabling 'suspend_utils' [ 4406]W(SM): msg with invalid func-id 90 or start/end byte has been discarded [ 3.127926] device-mapper: verity: data block 115493 is corrupted ta [ b l49oc]W(SM150437l sindeviDcent-nsmatypvplues frrm: V seetrnist dyt:b sd a 95kis r aoorupt0e d [ 4963]W(SM): WM == 2 [ 5631]I(SM): #########wdt1 enable
************************************************** ************************************************** *** DEBUG DUMP : dump_0 CREATED *** *** DEBUG DUMP : dump_0 CREATED *** ************************************************** ************************************************** [ 5.178979] BT: Loading driver [ 5.182297] Marvell Bluetooth USB driver [ 5.186410] bt_usb_probe: intf bdf1ac00 id 7f0eddf0 [ 5.191269] VID/PID = 1286/2044, Boot2 version = 3201 [ 5.203178] FW is Active [ 5.213635] BT: Create /dev/mbtchar0 [ 5.273003] BT: Create /dev/mfmchar0 [ 5.336080] BT: Driver loaded successfully [ 24632]W(SM): SOC is Alive !!! [ 28.003316] SysRq : Emergency Remount R/O [ 28.109353] Restarting system. [ 29451]I(SM): %%%%SM:Msg reset system%%%% [ 29455]I(SM): ******enter flow ---Sysreset to Active--- [ 29461]I(SM): peripheral_assert done [ 29464]I(SM): soc_assert done [ 29467]I(SM): mv_sm_power_socpoweroff done [ 29772]I(SM): mv_sm_power_socpoweron done [ 29832]I(SM): peripheral_assert done [ 29836]I(SM): soc_assert done [ 29932]I(SM): peripheral_deassert done [ 29936]W(SM): ### Wake Up Reason 0x0[ 29939]I(SM): soc_deassert done [ 0] sys_init start. boot_strap=0x00000514 (source=eMMC), boot_state=0xff [ 272] image verified, start at 0x00920000... tz kernel starting... MV88DE3114(BG2Q)-A1 total 4 cpus, v2.0.0.21, Aug 5 2014 14:39:52 0123[ 327] start_bootloader U▒ULAUNCH_ITM is set to zero board_number = 2 uiBoot = 255
I2C switch set as 0
I2C switch set as 1 --------- I2C Initialization ---------- I2C_INIT: I2C-2 bus I2C_INIT: I2C-1 bus I2C_INIT: I2C-0 bus DDR reg 0xF7CB0BAC value : 0x00021421 DDR reg 0xF7CB0C00 value : 0x00004031 leakage info 320. set Vcpu to 1300mV, default setting by hardware. core from 1200 to 1150 set Vcore to 1175mv set Vcore to 1150mv set Vcore to 1150 mv. flash_ts_init() success.
Файлы
Прошивки
Продажа
Литература
Статьи
Для просмотра сообщения Вы должны быть Участником форума. Для этого Вам необходимо 
Зарегистрировано всего