smartyu
Дата: Суббота, 25.01.2025, 14:25:16 | Сообщение # 1 | Отредактировал: smartyu - Воскресенье, 26.01.2025, 20:09:03
Автор темы
Участники
Мои познания в ремонте данного вида техники: НачинающийНаличие схемы: нет Состав аппарата.Марка и модель - Manta LED94901SШасси (если известно) - HK.T.NT72667V01Процесор -Модуль обработки сигнала (Main) - HK.T.NT72667V01Блок питания (PSU) - ER933LCD матрица - LSC490FN03Прочее (T-CON, инвертор...) - 4K модуль - HK.Z.NT72333V02, t-con - 16Y_BGU11BPCMTA4 V0.1 Текст сообщения: Сразу после включения матрица светится зеленым цветом. Прошивку с USB сам не подхватывает. Снял лог:
▒ BSP Revision: 15526 JTag enable card enable hs200!!! fgggggAC ON...... cid:17 DDRF:NT72667_HK_20160412_1200M_NR_Normal_boot.txt ======> Start DRAM Ren main reg 0x20 = 0x03, reg 0x0a = 0xa0 reg 0x21 = 0x03, reg 0x0b = 0xa0 reg 0x22 = 0x03, reg 0xda = 0x40 reg 0x23 = 0x03, reg 0xdb = 0x40 ======> End DRAM Scan ======> Start DRAM Ren sub reg 0x20 = 0x03, reg 0x0a = 0xd0 reg 0x21 = 0x03, reg 0x0b = 0xe0 reg 0x22 = 0x03, reg 0xda = 0x60 reg 0x23 = 0x03, reg 0xdb = 0x80 ======> End DRAM Scan VX1 = 0 SEP = 0 FRC = 0 enLvdsFormat = 0 LVDS mode BLEND_OSD_MODE SET default PLL SET default PLL u16PanelPowerOnDelay1 = 0 Onboot eMMC mode debug Power on AC! Power on mode: Always off! ▒TBC shutdown ARM! BSP Revision: 15526 JTag enable card enable hs200!!! fgggggAC ON...... cid:17 DDRF:NT72667_HK_20160412_1200M_NR_Normal_boot.txt ======> Start DRAM Ren main reg 0x20 = 0x03, reg 0x0a = 0xa0 reg 0x21 = 0x03, reg 0x0b = 0xa0 reg 0x22 = 0x03, reg 0xda = 0x40 reg 0x23 = 0x03, reg 0xdb = 0x30 ======> End DRAM Scan ======> Start DRAM Ren sub reg 0x20 = 0x03, reg 0x0a = 0xd0 reg 0x21 = 0x03, reg 0x0b = 0xe0 reg 0x22 = 0x03, reg 0xda = 0x60 reg 0x23 = 0x03, reg 0xdb = 0x80 ======> End DRAM Scan VX1 = 0 SEP = 0 FRC = 0 enLvdsFormat = 0 LVDS mode BLEND_OSD_MODE SET default PLL SET default PLL u16PanelPowerOnDelay1 = 0 Onboot eMMC mode debug Power on Key pad! dtb magic ok : edfe0dd0 xyyyyy last jump the kernel point : 4a08000 [ 0.000000] NVT SVN info : Last Changed Rev: 15930 [ 0.868316] init: platform ini before [ 0.874501] init: platform ini after [ 1.017611] init: trigger bootlogo [ 1.027109] [FEI_DEBUG]: Error ! open /dev/block/mmcblk0p1 fail(-1) [ 1.033426] [FEI_DEBUG]: read panel cfg file ERROR!!!(-1) [ 1.229406] [BOOT]START logo show : [FEI_DEBUG]: [ERROR]: Invalid OSD-Size, SrcWin: WxH = 2560x1440, DstWin: WxH = 0x0 [ 1.629424] init: /dev/hw_random not found [ 1.650962] init: /dev/hw_random not found [ 2.155614] init: Warning! Service preinstall needs a SELinux domain defined; please fix! CUSTOMIZED_APK=/system/usr/app PREINSTALL_RESULT=1 [ 2.247336] FUNC nvt_mem_create_node_from_dt name secure_os addr 0 size 100000 mode 1 [ 2.255288] FUNC nvt_mem_create_node_from_dt name vbi addr 100000 size 40000 mode 1 [ 2.263045] FUNC nvt_mem_create_node_from_dt name encrypt addr 140000 size 40000 mode 1 [ 2.271177] FUNC nvt_mem_create_node_from_dt name data_sync addr 180000 size 0 mode 0 [ 2.279109] FUNC nvt_mem_create_node_from_dt name encoder_n addr 180000 size 0 mode 1 [ 2.287038] FUNC nvt_mem_create_node_from_dt name encoder_s addr 180000 size 0 mode 0 [ 2.294981] FUNC nvt_mem_create_node_from_dt name aud addr 180000 size 800000 mode 1 [ 2.302808] FUNC nvt_mem_create_node_from_dt name dsp addr 980000 size 500000 mode 1 [ 2.310644] FUNC nvt_mem_create_node_from_dt name dtv_aud addr e80000 size 100000 mode 1 [ 2.318851] FUNC nvt_mem_create_node_from_dt name mm_aud addr f80000 size 200000 mode 1 [ 2.326956] FUNC nvt_mem_create_node_from_dt name emegerency_buffer addr 1180000 size 80000 mode 0 [ 2.336000] FUNC nvt_mem_create_node_from_dt name osd addr 1300000 size 3700000 mode 1 [ 2.344002] FUNC nvt_mem_create_node_from_dt name atv addr 3a900000 size 5700000 mode 1 [ 2.352100] FUNC nvt_mem_create_node_from_dt name muxer addr 40000000 size 0 mode 0 [ 2.359846] FUNC nvt_mem_create_node_from_dt name sw_decoder addr 80000000 size 3200000 mode 0 [ 2.368539] FUNC nvt_mem_create_node_from_dt name dtv addr 83200000 size 10400000 mode 0 [ 2.376711] FUNC nvt_mem_create_node_from_dt name va addr 93600000 size 380000 mode 0 [ 2.384635] FUNC nvt_mem_create_node_from_dt name disp_capture addr 93980000 size 0 mode 0 [ 2.393000] FUNC nvt_mem_create_node_from_dt name iframe addr 93980000 size 280000 mode 0 [ 2.401277] FUNC nvt_mem_create_node_from_dt name demux addr 93c00000 size 2600000 mode 1 [ 2.409539] FUNC nvt_mem_create_node_from_dt name isdb_buffer addr 96200000 size 0 mode 1 [ 2.417805] FUNC nvt_mem_create_node_from_dt name sbm addr 93c00000 size 2600000 mode 0 [ 2.425901] LINE 194,FUNC nvt_mem_create_node create memory node from dts [ 2.853700] ntktspu driver(major 127) installed. [ 2.858459] [ 2.858459] AUDIO-0.5.627,H1207 [20161207] [ 2.868782] kdvif: alloc_chrdev_region : retval = 0 [ 2.873665] kdvif: retval = 0 [ 2.876627] kdvif: class_create start [ 2.885475] genirq: Flags mismatch irq 45. 00000001 (NT.MPEG2IP.MAIN) vs. 00000001 (NT.MPEG2IP.MAIN) [ 2.894591] [ERR_DRV_FR2IP]MPEG2IP_Init: can't register fr2ip HW0 irq handler [ 2.919179] [MSG_DRV_CRYPTO]Novatek CRYPTO Driver registered !!!!!!Leon start(2)!!!! [ 2.954090] [ 2.954090] KER_LOG_DrvInit is called!! [ 2.997657] <no-node>: no devicenode given [ 3.129716] sdp-mc-audio.5 sdp-mc-audio.5: ASoC: Failed to add dec0 dolby compressed mode: -16 [ 3.138878] sdp-mc-audio.5 sdp-mc-audio.5: ASoC: Failed to add dec1 dolby compressed mode: -16 [ 3.194838] dtv_sub No such memory node [ 3.198982] share_mem No such memory node [ 3.220930] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_Initialise(), Line:10091 [ 3.227540] Platform Init Start! [ 3.231048] [DBG_DRV_PQ][DRV_PQ] DRV_PQ_Init(): [ 3.235490] Driver PQ Init Start! [ 3.239403] 3D Det Driver Init Start! [ 3.239412] 3D Det Driver Init HW Start! [ 3.239482] [ 3.239482] # gpDrvPQ3DDETTask ok [ 3.239485] 3D Det Driver Init HW Done! [ 3.239488] 3D Det Driver Init Done! [ 3.239572] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_PQSet_Common(), Line:17436 [ 3.239573] [ 3.239573] [ 3.239573] **********************PQ TABLE VERSION MESSAGE********************** [ 3.239581] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_PQSet_Common(), Line:17437 [ 3.239581] DATE : 2017/3/6 [ 3.239588] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_PQSet_Common(), Line:17438 [ 3.239589] VERSION: 0001 [ 3.239595] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_PQSet_Common(), Line:17439 [ 3.239596] 0****************************************************************26 [ 3.239596] [ 3.239596] [ 3.239723] [ERR_DRV_PQ][PLAT_PQ] PPQT_User_Get_Function_PAR(), Line:36395 [ 3.239724] PPQT_Get_Function_Header: PPQT_Get_Function_Header is NULL [ 3.239731] [ERR_DRV_PQ][PLAT_PQ] PLAT_PQ_AutoFunction_Init(), Line:25636 [ 3.239732] PLAT_PQ_AutoFunction_Init: PLAT_PQ_PPQT_Get_Par is NULL [ 3.239739] [ERR_DRV_PQ][PLAT_PQ] PLAT_PQ_Auto3DDETInit(), Line:32119 [ 3.239739] PLAT_PQ_Auto3DDETInit is NULL [ 3.239982] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_Initialise(), Line:10892 [ 3.239982] Platform Init HW Start! [ 3.240157] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_Set_AP_Gamma(), Line:3234 [ 3.240157] g_BootOnGammaFlag =1 , delay 50ms [ 3.293623] [ERR_DRV_PQ][PLAT_PQ_SHELL] PLAT_PQ_SHELL_ChkPQInit(), Line:134 [ 3.293624] PLAT_PQ is not initialize! [ 3.293651] [ERR_DRV_PQ][PLAT_PQ_SHELL] PLAT_PQ_SHELL_ChkPQInit(), Line:134 [ 3.293651] PLAT_PQ is not initialize! [ 3.293731] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_Initialise(), Line:10974 [ 3.293732] Platform Init HW Done! [ 3.293737] [DBG_DRV_PQ][PLAT_PQ] PLAT_PQ_Initialise(), Line:10988 [ 3.293738] Platform Init Done! [ 3.601666] [NTKETHMAC]: synopGMAC_probe. [ 3.606508] [NTKETHMAC] : Now Registering the netdevice [ 3.825772] NT72668-ehci fc1f0000.ehci: port 1 reset complete, port enabled [ 3.878273] rtk_btusb: btchr_open: Failed to get hci dev[NULL] [ 3.884370] rtk_btusb: btchr_open: Failed to get hci dev[NULL] [ 3.890689] rtk_btusb: btchr_open: Failed to get hci dev[NULL] [ 3.896850] rtk_btusb: btchr_open: Failed to get hci dev[NULL] [ 3.908377] init: cannot find '/system/bin/debuggerd64', disabling 'debuggerd64' [ 3.916078] init: cannot find '/system/bin/rild', disabling 'ril-daemon' Set ethernet: 7C:82:74:0D:7F:33 [ 3.929963] init: cannot find '/system/bin/install-recovery.sh', disabling 'flash_recovery' [ 3.951936] init: Warning! Service dmesg needs a SELinux domain defined; please fix! [ 3.960134] NT72668-ehci fc1f0000.ehci: port 1 reset complete, port enabled [ 4.016656] [NTKETHMAC]: Read FDET Reg timeout !! [ 4.035945] [NTKETHMAC]: [NVT Internal PHY] PHY ready shell@nt72668_hikeen:/ $ [ 4.289781] NT72668-ehci fc000000.ehci: port 1 reset complete, port enabled [ 4.409880] NT72668-ehci fc000000.ehci: port 1 reset complete, port enabled [BOOT] /home/huangds/QIYUE_POLAN_20170405/TV/TV/code/apps/avaapp/TIF_shel/TIF_shel.c: start mgr_init() Time = 4606 _tif_shel_source_cfg_GetNextCfgValue:0 drmModeGetEncoder= PASS [BOOT] PLAT_DRV_INI_Init finish Time = 4679 TVAPP_GetFactoryTestData:714 valueFacburn=0,valueP=0,valueM=0,valueF=0,valueR=0,valueZ=0 [ 4.849978] healthd: wakealarm_init: timerfd_create failed [ 4.855950] healthd: No charger supplies found APP_MGR_Fact_SetFactoryTestPanelValue -> (0 | 255) _TIF_SHEL_SetDefaultWBHRGBGain = 16 _TIF_SHEL_SetDefaultSysConfig = 2 (Utili_UBootdat_OPT)Miss item [panel_id]... (Utili_UBootdat_OPT)Miss item [board_id]... (Utili_UBootdat_OPT)Miss item [aq_index]... (Utili_UBootdat_OPT)Item [model_name] was done!!!!!! (Utili_UBootdat_OPT)Miss item [TPV_part_number]... (Utili_UBootdat_OPT)Miss item [panel_power_off_type]... (Utili_UBootdat_OPT)Miss item [panel_delay2]... (Utili_UBootdat_OPT)Miss item [panel_delay3]... (Utili_UBootdat_OPT)Miss item [panel_delay4]... (Utili_UBootdat_OPT)Miss item [panel_delay5]... (Utili_UBootdat_OPT)Miss item [factory_def_normal_gain_r]... (Utili_UBootdat_OPT)Miss item [factory_def_normal_gain_g]... (Utili_UBootdat_OPT)Miss item [factory_def_normal_gain_b]... (Utili_UBootdat_OPT)Miss item [factory_def_cool_gain_r]... (Utili_UBootdat_OPT)Miss item [factory_def_cool_gain_g]... (Utili_UBootdat_OPT)Miss item [factory_def_cool_gain_b]... (Utili_UBootdat_OPT)Miss item [factory_def_warm_gain_r]... (Utili_UBootdat_OPT)Miss item [factory_def_warm_gain_g]... (Utili_UBootdat_OPT)Miss item [factory_def_warm_gain_b]... (Utili_UBootdat_OPT)Miss item [panel_lvds_driving]... (Utili_UBootdat_OPT)Miss item [panel_lvds_format]... (Utili_UBootdat_OPT)Miss item [panel_h_flip]... (Utili_UBootdat_OPT)Miss item [panel_v_flip]... (Utili_UBootdat_OPT)Miss item [panel_ab_swap]... (Utili_UBootdat_OPT)Miss item [panel_pwm_limit]... (Utili_UBootdat_OPT)Miss item [panel_backlight_duty_inverse]... (Utili_UBootdat_OPT)Miss item [panel_pwr_inverse]... (Utili_UBootdat_OPT)Miss item [Poweron_Backlight_level]... (Utili_UBootdat_OPT)Miss item [panel_backlight_pwr_inverse]... (Utili_UBootdat_OPT)Miss item [CSM_Installation_date]... (Utili_UBootdat_OPT)Miss item [CSM_Option_code_1]... (Utili_UBootdat_OPT)Miss item [CSM_Option_code_2]... (Utili_UBootdat_OPT)Miss item [CSM_SSB]... (Utili_UBootdat_OPT)Miss item [CSM_Display]... (Utili_UBootdat_OPT)Miss item [CSM_PSU]... (Utili_UBootdat_OPT)Miss item [NVM_Version]... (Utili_UBootdat_OPT)Miss item [std_mode_pwm_gain]... (Utili_UBootdat_OPT)Miss item [eco_mode_pwm_gain]... (Utili_UBootdat_OPT)Miss item [std_mode_low_thd]... (Utili_UBootdat_OPT)Miss item [std_mode_mid_point]... (Utili_UBootdat_OPT)Miss item [std_mode_high_thd].[ 5.146003] [BOOT] START bootanimation show.. (Utili_UBootdat_OPT)Miss item [eco_mode_low_thd]... (Utili_UBootdat_OPT)Miss item [eco_mode_mid_point]... (Utili_UBootdat_OPT)Miss item [eco_mode_high_thd]... (Utili_UBootdat_OPT)Miss item [force_update_color_temp]... (Utili_UBootdat_OPT)Miss item [spdif_enable]... (Utili_UBootdat_OPT)Miss item [audio_gain_linein]... (Utili_UBootdat_OPT)Miss item [audio_gain_hdmi]... (Utili_UBootdat_OPT)Miss item [audio_gain_atv]... (Utili_UBootdat_OPT)Miss item [audio_gain_dtv]... (Utili_UBootdat_OPT)Miss item [audio_gain_usb]... (Utili_UBootdat_OPT)Miss item [vga_port_enable]... (Utili_UBootdat_OPT)Miss item [zero_detection_enable]... (Utili_UBootdat_OPT)Miss item [lvds_ssc_ratio]... (Utili_UBootdat_OPT)Miss item [lvds_ssc_freq]... (Utili_UBootdat_OPT)Miss item [emmc_ssc_ratio]... (Utili_UBootdat_OPT)Miss item [emmc_ssc_freq]... (Utili_UBootdat_OPT)Miss item [ddr_ssc_ratio]... (Utili_UBootdat_OPT)Miss item [ddr_ssc_freq]... (Utili_UBootdat_OPT)Miss item [ddr2_ssc_ratio]... (Utili_UBootdat_OPT)Miss item [ddr2_ssc_freq]... (Utili_UBootdat_OPT)Miss item [watch_dog_timeout]... (Utili_UBootdat_OPT)Miss item [vga_tx_rx_mode]... (Utili_UBootdat_OPT)Miss item [headphone_enable]... (Utili_UBootdat_OPT)Miss item [joystick_enable]... (Utili_UBootdat_OPT)Miss item [ambilight_enable]... (Utili_UBootdat_OPT)Miss item [hdmi_portindex_reverse]... (Utili_UBootdat_OPT)Miss item [hdmi_arc_support_port_id]... (Utili_UBootdat_OPT)Miss item [blue_tooth_enable]... (Utili_UBootdat_OPT)Miss item [freeview_hd_enable]... Config panel ID doesn't change u16PanelID = 16 | 16 APP_MGR_Fact_GetPanelBackLightLevel = 100 | 600 DEV_GPIO_Init_SetPWMInitParams -> 60000 | 0 (Utili_UBootdat_OPT)Item [model_name] was done!!!!!! dev_common [licl]======== c8ModelName = [HKYYMMXXCTi]=========== dev_common [DEV_COMMON_GetModelType] s_enModelType=7. (NIM_DTV)@@@@@@ DEV_NIM_DTV_Init: enModelType=7, gu32NimActiveModule=0x3 [BOOT] DEV_INI_Init finish Time = 5073 (NIM_DTV) ==>DEV_NIM_DTV_Open() NDAL demod commandline read: idtvserver (*) [(null) 5.210,718] ( 1904: 1904) DirectFB/Main: Initialization Start ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.7.1 |~~~~~~~~~~~~~~~~~~~~~~~~~~ © 2012-2013 DirectFB integrated media GmbH © 2001-2013 The world wide DirectFB Open Source Community © 2000-2004 Convergence (integrated media) GmbH ---------------------------------------------------------------- (*) [Main Thread 5.211,067] ( 1904: 1904) DirectFB/Core: Single Application Core. (2017-03-07 03:13) (*) [Main Thread 5.211,143] ( 1904: 1904) DirectFB/Build: SVN Revision 20170307110202 (*) [Main Thread 5.229,367] ( 1904: 1904) Direct/Thread: Started 'Fusion Dispatch' (2374) [MESSAGING - OTHER/0] <1040384>... (*) [Main Thread 5.290,500] ( 1904: 1904) Palette Buffer Phys = 0x031E2000 Addr = 0xB43EE000 (*) [Main Thread 5.290,947] ( 1904: 1904) A8 Palette Buffer Phys = 0x031E3000 Addr = 0xB43ED000 (*) [Main Thread 5.291,591] ( 1904: 1904) LAYER 0 -> PLANE 1 Buffer Phys = 0x01A08000 Size = 0x00FD2000 Addr = 0xB0DB4000 (*) [Main Thread 5.292,335] ( 1904: 1904) LAYER 1 -> PLANE 0 Buffer Phys = 0x01300000 Size = 0x00708000 Addr = 0xAF6DA000 (*) [Main Thread 5.292,675] ( 1904: 1904) LAYER 2 -> PLANE 2 Buffer Phys = 0x029DA000 Size = 0x00708000 Addr = 0xAE8CA000 (*) [Main Thread 5.293,148] ( 1904: 1904) DirectFB/Graphics: Novatek NVTGA GPU 1.0 (Novatek) (*) [Main Thread 5.303,186] ( 1904: 1904) DirectFB/Core/WM: Default 0.3 (directfb.org) (*) [Main Thread 5.303,662] ( 1904: 1904) Direct/Thread: Started 'Genefx' (2380) [DEFAULT - OTHER/0] <1040384>... (*) [Main Thread 5.303,957] ( 1904: 1904) NVTGA/Screen: Screen Resolution: 1920x1080 (*) [Main Thread 5.375,353] ( 1904: 1904) DirectFB/Main: Initialization End [ 5.771357] [MSG_DRV_CRYPTO]Open a CRYPTO device [BOOT] PLAT_INI_Init finish Time = 5761
Может быть дело в прошивке или куда смотреть?Добавлено (25.01.2025, 14:35:14) --------------------------------------------- Сверил проивку модуля HK.Z.NT72333V02 со скачанной отсюда. Прошивка совпадает
-->
технал8888
Дата: Суббота, 25.01.2025, 19:06:51 | Сообщение # 2
Участники
Для просмотра сообщения Вы должны быть
Участником форума. Для этого Вам необходимо
Зарегистрироваться и пройти Тест.
-->
smartyu
Дата: Суббота, 25.01.2025, 20:02:57 | Сообщение # 3
Автор темы
Участники
Для просмотра сообщения Вы должны быть
Участником форума. Для этого Вам необходимо
Зарегистрироваться и пройти Тест.
-->