Телевизор Philips 19PFL3507T/60 (TPM9.3E LA) циклически перезагружается на заставке. Прошу поделиться сервисной USB прошивкой. В прилагаемом ниже логе терминала присутствуют строки: Load T8032 FW fail!! и T8032 polling error: ack timeout!
Boot-
DRAM Channel A Calibration.
Byte 0 : DQS(0 ~ 28), Size 29, Set 12.
Byte 1 : DQS(0 ~ 28), Size 29, Set 12.
Byte 2 : DQS(7 ~ 29), Size 23, Set 16.
Byte 3 : DQS(0 ~ 26), Size 27, Set 11.
DRAM A Size = 256 Mbytes.
Boot
Start Pmain
0x00004000
NID=0x9510daec
LZHS addr:0x00100040
LZHS size:0x000a7840
LZHS checksum:0x00000091
Boot
Start Lmain
MT5365 Boot Loader v0.9 [PCMCIA]Set PCMCIA Access IF : SPI SPIHW_Init ----- Set SPI PinMux SPI dummy delay:0x10 External CI Version : MT5135 Output clock from main chip. PCMCIA Reset Demod GPIO=35, 0->1
SPI_SetPll(), spi clock: 27 Mhz External IC Initilization done MUSB none SoftReset 0x29424 = 0x01030000. MUSB pBase = 0xF0029000 init ok. MUSB none SoftReset 0x29424 = 0x01030000. MUSB pBase = 0xF002E000 init ok. Boot reason: A/C power on!!-------------use external edid, disable internal edid------------------ SIF_Master0: new design SIF_Master1: old design Boot reason: A/C power on!!T8032 init A/C on case loader stage... Load T8032 FW fail!! LDR_FlashCopy 0xf010 0x3d280 0x80 Switch NAND pinmux Detect NAND flash ID: 0x9510DAEC Detect SS K9F2G08U0B NAND flash(SLC): 256MB NAND_BDM_Mount: Partid=0, offset=0x0, size=0x200000 [BDM] Partition: 0, Bad Block Count: 0
Do USB upgrade
No USB device. USB upgrade stop Boot reason: A/C power on!!Boot reason: A/C power on!![PDWNC]PDWNC_TPV_DetermineNextState : u4Event = 0x6 PDWNC_TPV_DetermineNextState : u4Current = 1 PDWNC_TPV_DetermineNextState : system booting [PDWNC] Virgin Mode Status : 0x0, Offset :0x38 PDWNC_TPV_DetermineNextState : event = PDWNC_POWER_DOWN_AC_POWER Current = 0x1, Event = 0x6, Next = 0x1 Wakeup keypad array rCmd.u1SubCmd 31 Wakeup keypad array = 1 T8032 polling error: ack timeout!(Cmd = 0x21, SubCmd = 0x1f, Ack = 0) Boot reason: A/C power on!![PDWNC]PDWNC_ReadWakeupReason = 0x6 [PDWNC]Enter normal mode, LED changes to normal PDWNC_TPV_EnterNextState : u4Next = 0x1 Boot reason: A/C power on!! A_Mute GPIO=11 release AMP mute GPIO=cb release Reset Demod GPIO=23, 0->1
Display 0x00db05d8 background:0x00000000 2 bytes panel index is : 173 (0x ad) Find panel index 173 from EEPROM [LVDS] DVOPLL init control word only [LVDS] VOPLL Initialize successful ! LODFP. Boot reason: A/C power on!!---------- Panel[173] PANEL_M185XW01_VFT0 1366x768 ---------- PixelClk[Max=80000000, 60Hz=77058401, 50Hz=64279550, Min=63000000] HTotal[Max=2044, 60Hz=1608, 50Hz=1608, Min=1462] HSyncLen[60Hz=242, 50Hz=242] VTotal[Max=1108, 60Hz=798, 50Hz=798, Min=776] VClk[Max=63, Min=47] HSyncWidth=32, VSyncWidth=12, HPosition60Hz=0x800, HPosition50Hz=0x800, VPosition=1024 LVDS_NS, LVDS_ODD_SW_OFF, SINGLE_PORT, DISP_24BIT WFB_PANEL_RESET_OFF, PWM_LOW_PANEL_BRIGHT 3D_POLARIZED Backlight[High=0x0, Middle=0x0, Low=0x0] DimFreq60Hz=120, DimFreq50Hz=100 Delay[LvdsOn=40, BacklightOn=600, BacklightOff=2000, LvdsOff=50] MaxOverscan=50
Current panel setting is PANEL_M185XW01_VFT0 Backlight gpio=25, turn on value=0, LVDS gpio=16, turn on value=1 Pixel Shift=0 (1366 x 768) LDR_OsdDisplay(13, 0x00d50c50, 400, 100) Color:13 BmpAddr:0x00d50c50 Width:400 Height:100 OSD_SetTVEOut: 1 Panel 1366 x 768
NAND load lzhs header from 0x80000 to dram(0xfe6a50), size=2048 Decompression uboot to 0x00f00000...
NAND load image from 0x80000 to dram(0xfe6a50), size=0x3fcb3 secure boot ok LZHS hardware decode start LZHS hardware decode done Starting image...
U-Boot starts...
NAND Flash: Detect NAND flash ID: 0x9510DAEC Detect SS K9F2G08U0B NAND flash: 256MB 256 MiB Booting sequence is from NAND Flash In: serial Out: serial Err: serial SIF_Master0: new design SIF_Master1: old design eeprom para:4c0(6ffc90) u4MemLen:0x00000009 eeprom para:4c9(6ffc84) u4MemLen:0x00000009 eeprom para:4d2(6ffc78) u4MemLen:0x00000009 eeprom para:4c0(6ffc4c) u4MemLen:0x00000009 eeprom para:4c9(6ffc4c) u4MemLen:0x00000009 eeprom para:4d2(6ffc4c) u4MemLen:0x00000009 eeprom para:4c0(6ffec0) u4MemLen:0x00000009 Boot from kernelA and rootfs at partition 6 Hit any key to stop autoboot: 0 Partition rootfsA defined at mtdparts: ID:6, Offset:0x00c00000, Size:0x00a00000
Loading from nand0, offset 0x800000 Automatic boot of image at addr 0x00008000 ... eeprom para:4c0(6fe4d8) u4MemLen:0x00000009 Check signature from sigA Partition sigA defined at mtdparts: ID:2, Offset:0x00400000, Size:0x00200000 Loader succeeded in signature verification ## Booting kernel from Legacy Image at 00008000 ... XIP Kernel Image ... OK OK
Starting kernel ...
Uncompressing Linux............................................................................................ done, booting the kernel.
INIT: version 2.86 booting
Mounting local filesystems: mount mount: according to /proc/mounts, /dev/root is already mounted on / Running rc.local... net.ipv4.tcp_window_scaling = 6 # mount basic UBI device number 0, total 669 LEBs (84946944 bytes, 81.0 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) real 0m 0.23s user 0m 0.00s sys 0m 0.10s real 0m 0.04s user 0m 0.00s sys 0m 0.02s [AppManager]init [AppManager]init dfb start [AppManager]init dfb input thread's parent pid is 350 tid is 350 [DirectFB]: Wait to Init IR...! [AM] findProcessNameByPid = app_man [ProcessManager] startDefaultProcess [ProcessManager]init [AM] init succeed [AM] default process state '4' 'dtv_app_mtk' input thread pid is 350 tid is 354 original scheduler policy 0 scheduler nice -10 original child scheduler policy 0 prio 0 new child scheduler policy 2 prio 99 Start to wait IR event... [dtv_app_mtk]>[FM-Linux]Mount /dev/mtd8 to /basic successfully. [dtv_app_mtk]> [FM](/dev/mtd8) is mounted to (/basic) successfully(0) [dtv_app_mtk]> {CI_glue}:ci_eng_init [dtv_app_mtk]> {CI_glue}- expect PROD key [dtv_app_mtk]> {CI}CI_RegInterrupt_nfy [dtv_app_mtk]> {CI_glue}- c[1] [dtv_app_mtk]> MHEG5 TPS start to setup [dtv_app_mtk]> MHEG5 TPS setup failed to create dir(-6) [dtv_app_mtk]> MHEG5 TPS setup OK [dtv_app_mtk]> EEPROM size is 0x70. [dtv_app_mtk]> {DT} Real Time Clock is available on this system. [dtv_app_mtk]>
[dtv_app_mtk]> {SECM_DBG_INFO}fail to set request,PID 20,SRC(h_open_src<67216>,type<18,1>,flag<0x1>,connection<0>),SEC(flags<0xc0a>) [dtv_app_mtk]> <AM> wakeup reason = 6 [dtv_app_mtk]>
[dtv_app_mtk]> {SECM_DBG_INFO}fail to set request,PID 17,SRC(h_open_src<67216>,type<18,1>,flag<0x1>,connection<0>),SEC(flags<0x40a>) [dtv_app_mtk]>
[dtv_app_mtk]> {SECM_DBG_INFO}fail to set request,PID 16,SRC(h_open_src<67216>,type<18,1>,flag<0x1>,connection<0>),SEC(flags<0x40a>) [dtv_app_mtk]> [ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: default SUB [dtv_app_mtk]> [a_cfg_custom_bds_update_mutirc_state] state = 0