Boot-
EFUSE=3;
DRAM Channel A Calibration.
1T = (103 - 32) = 71 delay cells
Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell =16 ps
Byte 0 : Gating(-25 ~ 26), Size=52 .
Byte 1 : Gating(-25 ~ 25), Size=51 .
Byte 2 : Gating(-25 ~ 25), Size=51 .
Byte 3 : Gating(-25 ~ 25), Size=51 .
HW Byte 0 : DQS(-12 ~ 12), Size 25 , Set 0.
HW Byte 1 : DQS(-12 ~ 12), Size 25 , Set 0.
HW Byte 2 : DQS(-12 ~ 11), Size 24 , Set 0.
HW Byte 3 : DQS(-12 ~ 12), Size 25 , Set 0.
DATLAT calibration
first_step= 17 total pass= 6 best_step=19 .
TX HW Byte 0 : DQS(26 ~ 50), Size 25, Set 38.
TX HW Byte 1 : DQS(26 ~ 51), Size 26, Set 38.
TX HW Byte 2 : DQS(27 ~ 50), Size 24, Set 38.
TX HW Byte 3 : DQS(28 ~ 51), Size 24, Set 39.
DRAM A Size = 1024 Mbytes.
Boot
Start Pmain
EMMC boot
.
CID:0xd8af7603
:0x5206fe03
:0x47544634
:0x15010038
LZHS addr:0x00100040
LZHS size:0x000f2620
LZHS size:0x0005f97c
LZHS checksum:0x000000f1
LZHS begin
LZHS ok
Boot
Start Lmain

MT5863 Boot Loader v0.9
MUSB_Init : ++
It has 2 USB Port,is 1, 1, 0, 0(1=using, 0=not use).
USB0: Set GPIO-1 = 1.
USB0: Set GPIO-1 error.
USB1: Set GPIO-1 = 1.
USB1: Set GPIO-1 error.
USB Port 0 is initial.
USB Port 1 is initial.
Set port-0 to Host mode.
Set port-1 to Host mode.
Support network![MSDC] LOADER FAST READ EMMC!
[MSDC] Init config, cid = 0x15010038, dsc=0xd8af7603, rca=0x5206fe03, ocr=0x4754
4634
[MSDC] loader RCA 1, 1
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] MT22627:15010038:47544634:5206fe03:d8af7603
[MSDC] id1:00384754 id2:46345206
[MSDC] eMMC Name: UNKNOWN
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] Prepare set msdc Bus Clock as HS25(MHz),src 12 ,mode 0, div 4
[MSDC] Set Bus Clock as HS25(MHz) Success!,src 12 ,mode 0, div 4
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC] [eMMC2DRAM]enter into SDR50 Mode, max dtr 200000000
[MSDC] Prepare set msdc Bus Clock as HS0(MHz),src 0 ,mode 0, div 16
[MSDC] Set Bus Clock as HS0(MHz) Success!,src 0 ,mode 0, div 16
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 0 !
[MSDC] Prepare set msdc Bus Clock as HS50(MHz),src 12 ,mode 0, div 2
[MSDC] Set Bus Clock as HS50(MHz) Success!,src 12 ,mode 0, div 2
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC]
Saved info: id1 = 0x76035206, id2=0xfe034754,flag 0xaabbccdd,speedmode 5, dlycel
l 71
[MSDC] Support HS400, card type ext_csd[196]0x57
[MSDC] Support HS200, card type ext_csd[196]0x57
[MSDC] u4mask = 0x3
[MSDC] ID: 0x15010038, 0x47544634, 0x5206fe03, 0xd8af7603
[MSDC]
Cur info: id1 = 0x76035206, id2=0xfe034754,flag 0xaabbccdd,speedmode 5, dlycell
71
[MSDC]
-----The information is match, Alrady run autok before, ignore this time--
[MSDC] Load Param:
[MSDC] K_IOCON: 0x2000008
[MSDC] K_PAD_TUNE0: 0x2d2000
[MSDC] K_PAD_TUNE1: 0x0
[MSDC] K_PATCH_BIT0: 0x403c0006
[MSDC] K_PATCH_BIT1: 0xfffe4309
[MSDC] K_PATCH_BIT2: 0x448a1803
[MSDC] K_EMMC50_CFG0: 0xe88832
[MSDC] K_DAT_RD_DLY0: 0x4030404
[MSDC] K_DAT_RD_DLY1: 0x4020404
[MSDC] K_DAT_RD_DLY2: 0x0
[MSDC] K_DAT_RD_DLY3: 0x0
[MSDC] K_EMMC50_PAD_DS_TUNE: 0x11025
[MSDC] K_EMMC50_PAD_CMD_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT01_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT23_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT45_TUNE: 0x0
[MSDC] K_EMMC50_PAD_DAT67_TUNE: 0x0
[MSDC] Current speed mode 1, clock 50.
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] --ENTER RPMB--
[MSDC] --EXIT RPMB--
[MSDC] Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell = 16 ps
[MSDC] TCMGET_DLYCELL_PERT = 71
1st MAC in EEP is valid (c0:8a:cd:a7:c9:08)
Boot reason: A/C power on!!11111 u1AtmosEnable = 10
Remove Quiet Boot misc control in eeprom when Watchdog reason.

Normal zcc Start,using customer ir
IR DATA register : 0x 0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x dbb9f8, size: 21076)success!!
T8032 FW version: 6
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x69d80 0x80
<5507> getenv flag=0x1a01, len=0x0b
[readRecoveryCmd] readRecoveryCmd start
recovery cmd:,para:

Do USB upgrade
u1USBBlock = 0x01d09dc0
USB: Vbus turn up time = 314 ms, Max =1000 ms.
MUSB_GetInsert return 0

No USB device.

prLdrData->rDtvCfg.u1Upgrade_Ext :0x0

_fgDeviceType :0x1
USB upgrade stop

LDR_EEPUserDrvCheckMagic u4HeaderData=0x25125539, u4Magic=0x25125539
<5508> getenv flag=0x1a09, val=0x00
<5508> LDR_IsGoBootup prLdrData->u4WakeupReason:6
<5508> getenv flag=0x1a08, val=0x00
<5508> setenv flag=0x1421, val=0xff
<5508> LDR_IsGoBootup AT_READ_FLAG=0, AT_B_FLAG=0
go to standby when ac on at factory mode 0.

Error: Open file FAC_BOOT_WB_CONFIG_MTK5510.txt fail, RT710.dbg Loader_RT710_Sta
ndby
rt710.dbg ucI2cWrite_tuner OK
rt710.dbg ucI2cWrite_tuner OK
joe.dbg LDR I2C OK

cvte R842 standby
qiujunshuai R842_Init
qiujunshuai R842_Standby
Servoadc Channel1 frist update!!!, value is 1023
Servoadc Channel1 finish update!!!, value is 1023

Normal zcc Start,using customer ir
Disable VGA wakeup
powerdown usb port2
support WOL
wol off, MAC register switch to arm

star:mtcmos poweroff eth
11111 u1AtmosEnable = 10
loader The output gpio is 209 pfgSet0
loader The output gpio is 209 pfgSetis null
Standby
PDWNC_EnterPowerDown(200100,6)
SWITCH_T8032