Main 17MB82S V066a1 L4 AA БП. 17IPS61-3 V.1 160913 Панель LM196WD1 (TL) (A1) Тв. поступил с паянными SPI на майне U10 24Q32 и U12 24Q64. Прилагаю их содержание: https://mega.nz/#!MkJhlSxJ!weIP10qAbHHZD5RUJR9VfZzl373PLGwRmmJtHDiQo88 При включении в сеть загорается индикатор дежурного режима, после нажатия сетевой кнопки индикатор циклично моргает по 6 раз. Напряжения на майне 11.8, 5, 3.2, 1.5 без пульсаций. Снял лог загрузки:
Boot- DRAM Channel A Calibration. Byte 0 : Gating(1 ~ 96), Size=96, Mid=48, Set=48. Byte 1 : Gating(1 ~ 96), Size=96, Mid=48, Set=48. HW Byte 0 : DQS(24 ~ 50), Size 27, Set 37, HW_Set 38. HW Byte 1 : DQS(21 ~ 49), Size 29, Set 35, HW_Set 36. DRAM A Size = 128 Mbytes. Boot
Start Pmain
0x00002e70 Nor boot LZHS addr:0x00002ec0 LZHS size:0x00036550 LZHS checksum:0x00000087 Boot
Start Lmain
MT5389 Boot Loader v1.7 Boot reason: A/C power on Read partB current flag: 0Xcf3f40,0X200,0X3. Flash index :0,MenuID: 0xEF, DeviceID1: 0x40, DeviceID2: 0x17___________________________________ u4FlashSize = 0x800000___________________________________ Detect flash #0: WINBOND(W25Q64FV)________________________________________________________ Flash index :1,MenuID: 0xEF, DeviceID1: 0x40, DeviceID2: 0x16___________________________________ u4FlashSize = 0x400000___________________________________ Detect flash #1: WINBOND(W25Q32BV)________________________________________________________ vgaedid[i] = 0x0, i = 0, u4MemLen = 256. vgaedid[i] = 0xff, i = 1, u4MemLen = 256. vgaedid[i] = 0xff, i = 2, u4MemLen = 256. vgaedid[i] = 0xff, i = 3, u4MemLen = 256. vgaedid[i] = 0xff, i = 4, u4MemLen = 256. vgaedid[i] = 0xff, i = 5, u4MemLen = 256. vgaedid[i] = 0xff, i = 6, u4MemLen = 256. vgaedid[i] = 0x0, i = 7, u4MemLen = 256. vgaedid[i] = 0x58, i = 8, u4MemLen = 256. vgaedid[i] = 0xb3, i = 9, u4MemLen = 256.
Load VGA internal EDID................. Read partB current flag: 0Xcf3f30,0X300,0X3. hdmiedid[i] = 0x0, i = 0, u4MemLen = 256. hdmiedid[i] = 0xff, i = 1, u4MemLen = 256. hdmiedid[i] = 0xff, i = 2, u4MemLen = 256. hdmiedid[i] = 0xff, i = 3, u4MemLen = 256. hdmiedid[i] = 0xff, i = 4, u4MemLen = 256. hdmiedid[i] = 0xff, i = 5, u4MemLen = 256. hdmiedid[i] = 0xff, i = 6, u4MemLen = 256. hdmiedid[i] = 0x0, i = 7, u4MemLen = 256. hdmiedid[i] = 0x58, i = 8, u4MemLen = 256. hdmiedid[i] = 0xb3, i = 9, u4MemLen = 256. Load HDMI internal EDID................. CEC Physical offset 164 HDMI1 Physical adr 0x10 HDMI1 PA 0x10 HDMI1 checksum 0x40 HDMI2 PA 0x20 HDMI2 checksum 0x30 HDMI1 PA 0x10 HDMI1 checksum 0x40 pull high 1 2 3 .............. ### EEPROM read loader config failed!!! IR DATA register : 0x 0 Boot reason: A/C power on T8032 init A/C on case loader stage... Load T8032 FW (addr: 0x d2880c, size: 24576)success!! T8032 FW version: 78 T8032 change to loader stage... LDR_FlashCopy 0xf010 0x26180 0x80 PDWNC_SetT8032LEDBlinkOn 1___________________________ Boot reason: A/C power on Reset Demod GPIO=e, 0->1
[PCMCIA]Set PCMCIA Access IF : SPI VSPIHW_Init ----- Set SPI PinMux SPI dummy delay:0x10 External CI Version : MT5135 PCMCIA Reset Demod GPIO=14, 0->1
SPI_SetPll(), spi clock: 27 Mhz External IC Initilization done
NOR load lzhs header from:0x80000 loader eeprom dump succeed. ===>There is no MB82_DEVELOPER,will check MB82_AUTOTEST !!! ===>There is no MB82_AUTOTEST,will Boot Normally!!! Environment is root=/dev/mtdblock2 rootwait lpj=1814528 console=ttyMT0,115200n1 quiet mtdparts=mt53xx-nor:192k(loader),1216k(kernel),8M(root),64k(ro),1664k(rw),960k(ro2)
hdr->ih_load = 0x8000
hdr->ih_ep = 0x8040
hdr->ih_size = 0x11fa68
kernel_size = 0x3300000
====>copy kernel to dram normal_case :kernel_size=1178280
NOR boot
Do USB upgrade total mem size: 0x8000000, fbm addr:0x3bc0000, fbm size: 0x4440000 USB upgrade stop Boot reason: A/C power on Offset:0x00000000 Installed:0x11223345, 0x11223345 Boot reason: A/C power on dLastStandbyStatus = 1, dLastStandbyStatusOffset = 5, PDWNC_ReadWakeupReason() = 6 Boot reason: A/C power on PDWNC_SetT8032LEDBlinkOff 1___________________________ PDWNC_SetT8032LEDTurnOn 1___________________________ tt===========PDWNC_EnterPowerDown(0x0,0x0); Error Power button setting dTouchPadInstalledOffset:0x00000006 bPDWNC_IsTouchPadTableInstalled:0x11223344, 0x11223344 PDWNC_TouchPadTableResume, 0, 0 PDWNC_TouchPadTableResume, 0, 0 PDWNC_TouchPadTableResume, 25, 5 SetT8032ServoADC: 5, 129, 0, 0, 36943 SetT8032ServoADC: 5, 128, 0, 0, 58404 SetT8032ServoADC: 5, 130, 25, 5, 79866 PDWNC_ConfigScartWakeUp: 0, 1 PDWNC_SetT8032LEDBlinkOff 1___________________________ PDWNC_SetT8032LEDTurnOn 1___________________________ Disable VGA wakeup 0xf0028000[31:0]:0x8 0xf0028178[31:0]:0xa2 0xf0028040[31:0]:0x4 0xf0028044[31:0]:0xa000 0xf0028048[31:0]:0x0 0xf002804c[31:0]:0x4200 Place 1: 5 times read resrvd reg, check if T8032 alive. 1st:0xf002814c[31:0]:0x2001 2nd:0xf002814c[31:0]:0x20bc 3rd:0xf002814c[31:0]:0x2163 4th:0xf002814c[31:0]:0x220a 5th:0xf002814c[31:0]:0x22b1 Standby PDWNC_EnterPowerDown7: 0x0, 0x0_________________ PDWNC_EnterPowerDown: 0x0________________ SIF_Master0: new design SIF_Master1: old design 0x0..tt====PDWy
После нажатия BUTTON ON/OFF
Boot-Preloader T8032 ack !
DRAM Channel A Calibration. Byte 0 : Gating(1 ~ 96), Size=96, Mid=48, Set=48. Byte 1 : Gating(1 ~ 96), Size=96, Mid=48, Set=48. HW Byte 0 : DQS(24 ~ 52), Size 29, Set 38, HW_Set 38. HW Byte 1 : DQS(21 ~ 49), Size 29, Set 35, HW_Set 36. DRAM A Size = 128 Mbytes. Boot
Start Pmain
0x00002e70 Nor boot LZHS addr:0x00002ec0 LZHS size:0x00036550 LZHS checksum:0x00000087 Boot
Start Lmain
MT5389 Boot Loader v1.7 Boot reason:From T8032 is touchpad(3-way) power pull high 1 2 3 .............. ### EEPROM read loader config failed!!! IR DATA register : 0x 0 Boot reason:From T8032 is touchpad(3-way) power T8032 change to loader stage... LDR_FlashCopy 0xf010 0x26180 0x80 Flash index :0,MenuID: 0xEF, DeviceID1: 0x40, DeviceID2: 0x17___________________________________ u4FlashSize = 0x800000___________________________________ Detect flash #0: WINBOND(W25Q64FV)________________________________________________________ Flash index :1,MenuID: 0xEF, DeviceID1: 0x40, DeviceID2: 0x16___________________________________ u4FlashSize = 0x400000___________________________________ Detect flash #1: WINBOND(W25Q32BV)________________________________________________________ PDWNC_SetT8032LEDBlinkOn 1___________________________ Boot reason:From T8032 is touchpad(3-way) power Reset Demod GPIO=e, 0->1
[PCMCIA]Set PCMCIA Access IF : SPI VSPIHW_Init ----- Set SPI PinMux SPI dummy delay:0x10 External CI Version : MT5135 PCMCIA Reset Demod GPIO=14, 0->1
SPI_SetPll(), spi clock: 27 Mhz External IC Initilization done
NOR load lzhs header from:0x80000 loader eeprom dump succeed. ===>There is no MB82_DEVELOPER,will check MB82_AUTOTEST !!! ===>There is no MB82_AUTOTEST,will Boot Normally!!! Environment is root=/dev/mtdblock2 rootwait lpj=1814528 console=ttyMT0,115200n1 quiet mtdparts=mt53xx-nor:192k(loader),1216k(kernel),8M(root),64k(ro),1664k(rw),960k(ro2)
hdr->ih_load = 0x8000
hdr->ih_ep = 0x8040
hdr->ih_size = 0x11fa68
kernel_size = 0x3300000
====>copy kernel to dram normal_case :kernel_size=1178280
NOR boot
Do USB upgrade total mem size: 0x8000000, fbm addr:0x3bc0000, fbm size: 0x4440000 USB upgrade stop Boot reason:From T8032 is touchpad(3-way) power Offset:0x00000000 Installed:0x11223345, 0x11223345 Boot reason:From T8032 is touchpad(3-way) power dLastStandbyStatus = 1, dLastStandbyStatusOffset = 5, PDWNC_ReadWakeupReason() = 29 Boot reason:From T8032 is touchpad(3-way) power PDWNC_SetT8032LEDBlinkOn 1___________________________ Uncompressing Linux... done, booting the kernel.
<mt53xx_nor_init>hank:V0.6.9m(protect 0 flash)... Flash Index: 0, MenuID: ef, DevID1: 40, DevID2: 17 Setup flash information successful, support list index: 29 Flash Index: 1, MenuID: ef, DevID1: 40, DevID2: 16 Setup flash information successful, support list index: 28
INIT: version 2.88 booting
Loading /etc/profile... Running rc.local.partial... 5+0 records in 5+0 records out 5120 bytes (5.0KB) copied, 0.013274 seconds, 376.7KB/s 5058+0 records in 5058+0 records out 5058 bytes (4.9KB) copied, 0.033624 seconds, 146.9KB/s mount ro2... 58+0 records in 58+0 records out 59392 bytes (58.0KB) copied, 0.019495 seconds, 2.9MB/s Loading dtv_driver_adapt ... Running autorun.sh ... NORMAL start ... SQUASHFS error: xz_dec_run error, data probably corrupt [vestel.bin(256)]squashfs_xz_uncompress .
SQUASHFS error: squashfs_read_data failed to read block 0x5e5338 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 SQUASHFS error: Unable to read data cache entry [5e5338] SQUASHFS error: Unable to read page, block 5e5338, size abe0 pgd = c2e30000 [002eab10] *pgd=02eb4031, pte=c2eb4ba8, *pte=00000000, *ppte=00000000 kernel BUG at /share/tarball_148/release/vm_linux/chiling/kernel/linux-2.6.35/arch/arm/mm/fault.c:207! Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = c2e30000 [00000000] *pgd=02e84031, pte=c2e84800, *pte=00000000, *ppte=00000000 Internal error: Oops: 817 [#1] PREEMPT last sysfs file: Modules linked in: ioctl_reg_func(P) CPU: 0 Tainted: P (2.6.35 #1) PC is at __bug+0x1c/0x28 LR is at __bug+0x18/0x28 pc : [<c00211a8>] lr : [<c00211a4>] psr: 60000113 sp : c1b0be30 ip : 00000000 fp : bed4aa3c r10: c02100d4 r9 : 00030002 r8 : c2c692a0 r7 : 80000007 r6 : 00000007 r5 : 002eab10 r4 : c2c690e0 r3 : 00000000 r2 : c1b0be24 r1 : c01d2296 r0 : 0000006d Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 00c5387d Table: 02e30008 DAC: 00000015
Load VGA internal EDID................. Read partB current flag: 0Xcf3f30,0X300,0X3. hdmiedid[i] = 0x0, i = 0, u4MemLen = 256. hdmiedid[i] = 0xff, i = 1, u4MemLen = 256. hdmiedid[i] = 0xff, i = 2, u4MemLen = 256. hdmiedid[i] = 0xff, i = 3, u4MemLen = 256. hdmiedid[i] = 0xff, i = 4, u4MemLen = 256. hdmiedid[i] = 0xff, i = 5, u4MemLen = 256. hdmiedid[i] = 0xff, i = 6, u4MemLen = 256. hdmiedid[i] = 0x0, i = 7, u4MemLen = 256. hdmiedid[i] = 0x58, i = 8, u4MemLen = 256. hdmiedid[i] = 0xb3, i = 9, u4MemLen = 256. Load HDMI internal EDID................. CEC Physical offset 164 HDMI1 Physical adr 0x10 HDMI1 PA 0x10 HDMI1 checksum 0x40 HDMI2 PA 0x20 HDMI2 checksum 0x30 HDMI1 PA 0x10 HDMI1 checksum 0x40 pull high 1 2 3 .............. ### EEPROM read loader config failed!!! IR DATA register : 0x 0 Boot reason: Watch dog0 reset (0x1000000) T8032 init A/C on case loader stage... Load T8032 FW (addr: 0x d2880c, size: 24576)success!! T8032 FW version: 78 T8032 change to loader stage... LDR_FlashCopy 0xf010 0x26180 0x80 PDWNC_SetT8032LEDBlinkOn 1___________________________ Boot reason: Watch dog0 reset (0x1000000) Reset Demod GPIO=e, 0->1
[PCMCIA]Set PCMCIA Access IF : SPI VSPIHW_Init ----- Set SPI PinMux SPI dummy delay:0x10 External CI Version : MT5135 PCMCIA Reset Demod GPIO=14, 0->1
SPI_SetPll(), spi clock: 27 Mhz External IC Initilization done
NOR load lzhs header from:0x80000 loader eeprom dump succeed. ===>There is no MB82_DEVELOPER,will check MB82_AUTOTEST !!! ===>There is no MB82_AUTOTEST,will Boot Normally!!! Environment is root=/dev/mtdblock2 rootwait lpj=1814528 console=ttyMT0,115200n1 quiet mtdparts=mt53xx-nor:192k(loader),1216k(kernel),8M(root),64k(ro),1664k(rw),960k(ro2)
hdr->ih_load = 0x8000
hdr->ih_ep = 0x8040
hdr->ih_size = 0x11fa68
kernel_size = 0x3300000
====>copy kernel to dram normal_case :kernel_size=1178280
NOR boot
Do USB upgrade total mem size: 0x8000000, fbm addr:0x3bc0000, fbm size: 0x4440000 USB upgrade stop Boot reason: Watch dog0 reset (0x1000000) RESRV2:0x0.... Offset:0x00000000 Installed:0x11223345, 0x11223345 Boot reason: Watch dog0 reset (0x1000000) dLastStandbyStatus = 1, dLastStandbyStatusOffset = 5, PDWNC_ReadWakeupReason() = 33 Boot reason: Watch dog0 reset (0x1000000) PDWNC_SetT8032LEDBlinkOn 1___________________________ Uncompressing Linux... done, booting the kernel.
<mt53xx_nor_init>hank:V0.6.9m(protect 0 flash)... Flash Index: 0, MenuID: ef, DevID1: 40, DevID2: 17 Setup flash information successful, support list index: 29 Flash Index: 1, MenuID: ef, DevID1: 40, DevID2: 16 Setup flash information successful, support list index: 28
INIT: version 2.88 booting
Loading /etc/profile... Running rc.local.partial... 5+0 records in 5+0 records out 5120 bytes (5.0KB) copied, 0.013240 seconds, 377.6KB/s 5058+0 records in 5058+0 records out 5058 bytes (4.9KB) copied, 0.033638 seconds, 146.8KB/s mount ro2... 58+0 records in 58+0 records out 59392 bytes (58.0KB) copied, 0.020512 seconds, 2.8MB/s Loading dtv_driver_adapt ... Running autorun.sh ... NORMAL start ... <0> Дальше циклическая перезагрузка лога.
Boot- DRAM Channel A Calibration. Byte 0 : Gating(1 ~ 96), Size=96, Mid=48, Set=48. Byte 1 : Gating(1 ~ 96), Size=96, Mid=48, Set=48. HW Byte 0 : DQS(24 ~ 50), Size 27, Set 37, HW_Set 38. HW Byte 1 : DQS(21 ~ 49), Size 29, Set 35, HW_Set 36. DRAM A Size = 128 Mbytes. Boot
Start Pmain
0x00002e70 Nor boot LZHS addr:0x00002ec0 LZHS size:0x00036168 LZHS checksum:0x000000f4 Boot
Start Lmain
MT5389 Boot Loader v1.7 Boot reason: A/C power on Read partB current flag: 0Xcf3f40,0X200,0X3. Flash index :0,MenuID: 0xEF, DeviceID1: 0x40, DeviceID2: 0x17___________________________________ u4FlashSize = 0x800000___________________________________ Detect flash #0: WINBOND(W25Q64FV)________________________________________________________ Flash index :1,MenuID: 0xC8, DeviceID1: 0x40, DeviceID2: 0x16___________________________________ u4FlashSize = 0x0___________________________________ Detect flash #1: 32Mb________________________________________________________ vgaedid[i] = 0x0, i = 0, u4MemLen = 256. vgaedid[i] = 0xff, i = 1, u4MemLen = 256. vgaedid[i] = 0xff, i = 2, u4MemLen = 256. vgaedid[i] = 0xff, i = 3, u4MemLen = 256. vgaedid[i] = 0xff, i = 4, u4MemLen = 256. vgaedid[i] = 0xff, i = 5, u4MemLen = 256. vgaedid[i] = 0xff, i = 6, u4MemLen = 256. vgaedid[i] = 0x0, i = 7, u4MemLen = 256. vgaedid[i] = 0x58, i = 8, u4MemLen = 256. vgaedid[i] = 0xb3, i = 9, u4MemLen = 256.
Load VGA internal EDID................. Read partB current flag: 0Xcf3f30,0X300,0X3. hdmiedid[i] = 0x0, i = 0, u4MemLen = 256. hdmiedid[i] = 0xff, i = 1, u4MemLen = 256. hdmiedid[i] = 0xff, i = 2, u4MemLen = 256. hdmiedid[i] = 0xff, i = 3, u4MemLen = 256. hdmiedid[i] = 0xff, i = 4, u4MemLen = 256. hdmiedid[i] = 0xff, i = 5, u4MemLen = 256. hdmiedid[i] = 0xff, i = 6, u4MemLen = 256. hdmiedid[i] = 0x0, i = 7, u4MemLen = 256. hdmiedid[i] = 0x58, i = 8, u4MemLen = 256. hdmiedid[i] = 0xb3, i = 9, u4MemLen = 256. Load HDMI internal EDID................. CEC Physical offset 164 HDMI1 Physical adr 0x10 HDMI1 PA 0x10 HDMI1 checksum 0x40 HDMI2 PA 0x20 HDMI2 checksum 0x30 HDMI1 PA 0x10 HDMI1 checksum 0x40 pull high 1 2 3 .............. ### EEPROM read loader config failed!!! IR DATA register : 0x 0 Boot reason: A/C power on T8032 init A/C on case loader stage... Load T8032 FW (addr: 0x d28bbc, size: 24576)success!! T8032 FW version: 78 T8032 change to loader stage... LDR_FlashCopy 0xf010 0x26100 0x80 PDWNC_SetT8032LEDBlinkOn 1___________________________ Boot reason: A/C power on Reset Demod GPIO=e, 0->1
[PCMCIA]Set PCMCIA Access IF : SPI SPIHW_Init ----- Set SPI PinMux SPI dummy delay:0x10 External CI Version : MT5135 PCMCIA Reset Demod GPIO=14, 0->1
SPI_SetPll(), spi clock: 27 Mhz External IC Initilization done
NOR load lzhs header from:0x80000
Спросил у автора прошивку мс U12 25Q64, её у него не оказалось. Перепробовал пару разных прошивок 25Q64, тв не включился. Уважаемые знатоки, может кто из лога увидит проблему железа, или всё таки нужен дамп U12 25Q64.
Файлы
Прошивки
Продажа
Литература
Статьи
Для просмотра сообщения Вы должны быть Участником форума. Для этого Вам необходимо 
Зарегистрировано всего