Плата под названием T-GX3235_T2_115MM V1.1не ловит сигнал, литы поменял 1,8, 3,3 1,2 вольта были, пропал демодулятор по моему atmb7821b не - помогло потом прогорел с флюсом его и входную мс mxl608 и каналы появились при поиске но после него нет сигнала. Потом с доноров не годных снимал их и подставлял,некоторые в кз, демодуляторы, а некоторые нет, а входные с доноров все в кз. Короче не вышло также нет сигнала. Из за чего это может быть? Возле входной мс есть дроссель так вот по моему никуда вызвонить не удалось.
Добавлено (10.02.2026, 08:33:04) --------------------------------------------- Вот лог. Что по нему можно сказать?
error : configure DAC must set ENABLE_GX_OTP = y !
Partition Version : 102 Partition Count : 6 Write Protect : TRUE CRC32 Enable : TRUE Table CRC32 : 56DEC2C3 ============================================================================================== ID NAME FS CRC32 START TOTAL_SIZE MAIN_SIZE USED_SIZE Use% RES_SIZE ============================================================================================== 0 BOOT RAW 1A57B7DD 00000000 64 KB 64 KB 64880 B 98% 0 MB 1 TABLE RAW 00010000 512 B 512 B 512 B 100% 0 MB 2 LOGO RAW 83AF8F68 00010200 65024 B 65024 B 59230 B 91% 0 MB 3 KERNEL RAW CD0358C1 00020000 2560 KB 2560 KB 2557 KB 99% 0 MB 4 ROOT CRAMFS 8A57068C 002a0000 896 KB 896 KB 880 KB 98% 0 MB 5 DATA MINIFS FF000000 00380000 512 KB 512 KB 1 B 0% 0 MB ----------------------------------------------------------------------------------------------
GxLoader v1.9.6-x 20170220
cpu family : CSKY chip model : gx6605s board type : 6605s memory size : 64 MB Flash type : zb25vq32 Flash size : 4 MB warning: board-init not call function enable_dac, will open cvbs & ypbpr default. show jpeg logo ... romfs_load file ecos.bin.lzma.
Decompress kernel ...ok The total boot time is: 5 s (5550 ms) cmdline str: mem. mem_info bank[0]start:90000000, size:1800000. mem_info bank[1]start:91800000, size:2800000. The whole mem size: 4000000. wdt_init, 6605. -----------[bsp_panel_mod_init] ret = 0---------- -----------[bsp_gpio_mod_init] ret = 0---------- jedec_id=5e4016, ext_id=5e40 ---jedec_id=0x5e4016----- ___usbwifi_init____ usbnet dev supported! [cyg_net_init] Init: mbinit(0x0) [cyg_net_init] Init: cyg_net_init_devs(0x0) cyg_net_init_devs Init device 'ra0' ___rt_ecos_init____ cyg_net_init_devs Init device '/dev/eth1' cyg_net_init_devs Init device empty '0x90654180' [cyg_net_init] Init: loopattach(0x0) [cyg_net_init] Init: cyg_ppp_pppattach(0x0) [cyg_net_init] Init: ifinit(0x0) [cyg_net_init] Init: domaininit(0x0) [cyg_net_init] Init: cyg_net_add_domain(0x905c4ab8) New domain internet at 0x0 sack hole zone : 0x906e2900 [cyg_net_init] Init: cyg_net_add_domain(0x905c4768) New domain route at 0x0 [cyg_net_init] Init: call_route_init(0x0) [cyg_net_init] Done USB HCD: device gx-ehci, build at 10:43:10 Mar 13 2019 ehci: 0x908d93cc ehci->hcs_params=0x2112, num: 2 hcs_params=0x2112 flag=0x0. hub1=0x2000 hub2=0x2000 ehci base=0xa0900000 operational base= 0xa0900010 gx-ehci gx-ehci.0: gx EHCI gx-ehci gx-ehci.0: new USB bus registered, assigned bus number 1 ehci_mem_init():ehci->async->qh_dma=0x108e5900 ehci_mem_init():sizeof qtd: 96. ehci_mem_init():sizeof qh: 128. gx-ehci gx-ehci.0: supports USB remote wakeup gx-ehci gx-ehci.0: irq 59, io mem 0xa0900000 usb usb1: default language 0x0409 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-:1.0 (config #1, interface 0) hub 1-:1.0: usb_probe_interface hub 1-:1.0: usb_probe_interface - got id hub 1-:1.0: USB hub found hub 1-:1.0: 2 ports detected hub 1-:1.0: standalone hub hub 1-:1.0: individual port power switching hub 1-:1.0: individual port over-current protection hub 1-:1.0: Single TT hub 1-:1.0: TT requires at most 8 FS bit times (666 ns) hub 1-:1.0: power on to power good time: 20ms hub 1-:1.0: local power source is good hub 1-:1.0: enabling power on all ports USB HCD: device gx-ohci, build at 10:43:11 Mar 13 2019
--------ohci base= 0xa0a00000 <7>: starting gx OHCI USB Controller no sem_wait. <7>: Clock to USB host has been enabled gx-ohci gx-ohci.0: gx OHCI gx-ohci gx-ohci.0: new USB bus registered, assigned bus number 2 gx-ohci gx-ohci.0: supports USB remote wakeup gx-ohci gx-ohci.0: irq 58, io mem 0xa0a00000 usb usb2: default language 0x0409 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: usb_probe_device usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-:1.0 (config #1, interface 0) hub 2-:1.0: usb_probe_interface hub 2-:1.0: usb_probe_interface - got id hub 2-:1.0: USB hub found hub 2-:1.0: 1 port detected hub 2-:1.0: standalone hub hub 2-:1.0: no power switching (usb 1.0) hub 2-:1.0: global over-current protection hub 2-:1.0: power on to power good time: 4ms hub 2-:1.0: local power source is good hub 2-:1.0: no over-current condition exists hub 2-:1.0: trying to enable port power on non-switchable hub
--------ohci base= 0xa0b00000 <7>: starting gx OHCI USB Controller no sem_wait. <7>: Clock to USB host has been enabled gx-ohci gx-ohci.1: gx OHCI gx-ohci gx-ohci.1: new USB bus registered, assigned bus number 3 gx-ohci gx-ohci.1: supports USB remote wakeup gx-ohci gx-ohci.1: irq 57, io mem 0xa0b00000 usb usb3: default language 0x0409 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-:1.0 (config #1, interface 0) hub 3-:1.0: usb_probe_interface hub 3-:1.0: usb_probe_interface - got id hub 3-:1.0: USB hub found hub 3-:1.0: 1 port detected hub 3-:1.0: standalone hub hub 3-:1.0: no power switching (usb 1.0) hub 3-:1.0: global over-current protection hub 3-:1.0: power on to power good time: 4ms hub 3-:1.0: local power source is good hub 3-:1.0: no over-current condition exists hub 3-:1.0: trying to enable port power on non-switchable hub rtusb init rt5370 ---> rtusb init mt7601 ---> registering sr9700 driver ... OK registering dm9601 driver ... OK registering cdc driver ... OK registering asix driver ... OK registering sr9800 driver ... OK registering rtl8152 driver ... OK goxceed vserson v1.9.6-4+patch warning: want to protect len 0x380000; actually protect len usb_hcd_poll_rh_status, 531. 0x200000, please confirm. Flash write protect(BOTTOM): 0 - 200000 INFO: mount /dev/flash/0/0x2a0000,0xe0000, partition id = 4 usb_hcd_poll_rh_status, 531. usb_hcd_poll_rh_status, 531. MPEG: date 2018.11.05 ver 1.1.2.8 [FB]:start:0x91800000, size:0x2800000 block 1 is bad block 4 is bad
Добавлено (10.02.2026, 09:02:42) --------------------------------------------- А вот мой личный ясин DVB9999
▒p▒X▒UN
error : configure DAC must set ENABLE_GX_OTP = y !
Partition Version : 102 Partition Count : 6 Write Protect : TRUE CRC32 Enable : TRUE Table CRC32 : 3A245FF7 ============================================================================================== ID NAME FS CRC32 START TOTAL_SIZE MAIN_SIZE USED_SIZE Use% RES_SIZE ============================================================================================== 0 BOOT RAW 321CC0D5 00000000 64 KB 64 KB 64880 B 98% 0 MB 1 TABLE RAW 00010000 512 B 512 B 512 B 100% 0 MB 2 LOGO RAW 16FA42C7 00010200 65024 B 65024 B 53037 B 81% 0 MB 3 KERNEL RAW 70DFBF56 00020000 2560 KB 2560 KB 2556 KB 99% 0 MB 4 ROOT CRAMFS 0C794C68 002a0000 896 KB 896 KB 876 KB 97% 0 MB 5 DATA MINIFS FF000000 00380000 512 KB 512 KB 1 B 0% 0 MB ----------------------------------------------------------------------------------------------
GxLoader v1.9.6-x 20170220
cpu family : CSKY chip model : gx6605s board type : 6605s memory size : 64 MB Flash type : zb25vq32 Flash size : 4 MB warning: board-init not call function enable_dac, will open cvbs & ypbpr default. show jpeg logo ... romfs_load file ecos.bin.lzma.
Decompress kernel ...ok The total boot time is: 5 s (5534 ms) cmdline str: mem. mem_info bank[0]start:90000000, size:1800000. mem_info bank[1]start:91800000, size:2800000. The whole mem size: 4000000. wdt_init, 6605. -----------[bsp_panel_mod_init] ret = 0---------- -----------[bsp_gpio_mod_init] ret = 0---------- jedec_id=5e4016, ext_id=5e40 ---jedec_id=0x5e4016----- ___usbwifi_init____ usbnet dev supported! [cyg_net_init] Init: mbinit(0x0) [cyg_net_init] Init: cyg_net_init_devs(0x0) cyg_net_init_devs Init device 'ra0' ___rt_ecos_init____ cyg_net_init_devs Init device '/dev/eth1' cyg_net_init_devs Init device empty '0x906541a0' [cyg_net_init] Init: loopattach(0x0) [cyg_net_init] Init: cyg_ppp_pppattach(0x0) [cyg_net_init] Init: ifinit(0x0) [cyg_net_init] Init: domaininit(0x0) [cyg_net_init] Init: cyg_net_add_domain(0x905c4ad8) New domain internet at 0x0 sack hole zone : 0x906e2920 [cyg_net_init] Init: cyg_net_add_domain(0x905c4788) New domain route at 0x0 [cyg_net_init] Init: call_route_init(0x0) [cyg_net_init] Done USB HCD: device gx-ehci, build at 10:43:10 Mar 13 2019 ehci: 0x908d93ec ehci->hcs_params=0x2112, num: 2 hcs_params=0x2112 flag=0x0. hub1=0x2000 hub2=0x2000 ehci base=0xa0900000 operational base= 0xa0900010 gx-ehci gx-ehci.0: gx EHCI gx-ehci gx-ehci.0: new USB bus registered, assigned bus number 1 ehci_mem_init():ehci->async->qh_dma=0x108e5920 ehci_mem_init():sizeof qtd: 96. ehci_mem_init():sizeof qh: 128. gx-ehci gx-ehci.0: supports USB remote wakeup gx-ehci gx-ehci.0: irq 59, io mem 0xa0900000 usb usb1: default language 0x0409 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-:1.0 (config #1, interface 0) hub 1-:1.0: usb_probe_interface hub 1-:1.0: usb_probe_interface - got id hub 1-:1.0: USB hub found hub 1-:1.0: 2 ports detected hub 1-:1.0: standalone hub hub 1-:1.0: individual port power switching hub 1-:1.0: individual port over-current protection hub 1-:1.0: Single TT hub 1-:1.0: TT requires at most 8 FS bit times (666 ns) hub 1-:1.0: power on to power good time: 20ms hub 1-:1.0: local power source is good hub 1-:1.0: enabling power on all ports USB HCD: device gx-ohci, build at 10:43:11 Mar 13 2019
--------ohci base= 0xa0a00000 <7>: starting gx OHCI USB Controller no sem_wait. <7>: Clock to USB host has been enabled gx-ohci gx-ohci.0: gx OHCI gx-ohci gx-ohci.0: new USB bus registered, assigned bus number 2 gx-ohci gx-ohci.0: supports USB remote wakeup gx-ohci gx-ohci.0: irq 58, io mem 0xa0a00000 usb usb2: default language 0x0409 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: usb_probe_device usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-:1.0 (config #1, interface 0) hub 2-:1.0: usb_probe_interface hub 2-:1.0: usb_probe_interface - got id hub 2-:1.0: USB hub found hub 2-:1.0: 1 port detected hub 2-:1.0: standalone hub hub 2-:1.0: no power switching (usb 1.0) hub 2-:1.0: global over-current protection hub 2-:1.0: power on to power good time: 4ms hub 2-:1.0: local power source is good hub 2-:1.0: no over-current condition exists hub 2-:1.0: trying to enable port power on non-switchable hub
--------ohci base= 0xa0b00000 <7>: starting gx OHCI USB Controller no sem_wait. <7>: Clock to USB host has been enabled gx-ohci gx-ohci.1: gx OHCI gx-ohci gx-ohci.1: new USB bus registered, assigned bus number 3 gx-ohci gx-ohci.1: supports USB remote wakeup gx-ohci gx-ohci.1: irq 57, io mem 0xa0b00000 usb usb3: default language 0x0409 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-:1.0 (config #1, interface 0) hub 3-:1.0: usb_probe_interface hub 3-:1.0: usb_probe_interface - got id hub 3-:1.0: USB hub found hub 3-:1.0: 1 port detected hub 3-:1.0: standalone hub hub 3-:1.0: no power switching (usb 1.0) hub 3-:1.0: global over-current protection hub 3-:1.0: power on to power good time: 4ms hub 3-:1.0: local power source is good hub 3-:1.0: no over-current condition exists hub 3-:1.0: trying to enable port power on non-switchable hub rtusb init rt5370 ---> rtusb init mt7601 ---> registering sr9700 driver ... OK registering dm9601 driver ... OK registering cdc driver ... OK registering asix driver ... OK registering sr9800 driver ... OK registering rtl8152 driver ... OK goxceed vserson v1.9.6-4+patch warning: want to protect len 0x380000; actually protect len usb_hcd_poll_rh_status, 531. 0x200000, please confirm. Flash write protect(BOTTOM): 0 - 200000 INFO: mount /dev/flash/0/0x2a0000,0xe0000, partition id = 4 usb_hcd_poll_rh_status, 531. usb_hcd_poll_rh_status, 531. MPEG: date 2018.11.05 ver 1.1.2.8 [FB]:start:0x91800000, size:0x2800000
[AV-MSC] : more then 100 persent drop hdmi out data 1, source 0, edid codes: 0 spdif out data 1, source 0 VPU_GetVersionInfo(): 16093010 [GUI] ######## widget : wnd_full_screen ###### signal : app_full_screen_create excute too long ######## [GUI_Init] Success [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked [APP INIT]: 6660 ms, total 7650 ms [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 ------------------->No signal Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 ------------------->No signal [Error]ATBM204ChipStatusGet(0),ATBM2040 is not initialized! demodulator lock status:0 bandwidth = 0. TunerAuto_set_params TUNER_MXL608 freq=674000000 bandwith=0 Tuner locked ------------------->No signal
Файлы
Прошивки
Продажа
Литература
Статьи
Для просмотра сообщения Вы должны быть Участником форума. Для этого Вам необходимо 
Зарегистрировано всего