Добавлено (30.04.2026, 19:52:20)
---------------------------------------------
Подключил терминал но не знаю что и где смотреть подскажите знающие люди и то ли это вообще?
А то от обилия прочитаной информации голова кругом идёт
А зверушку хочется оживить
IPL ga5271e7
D-1b
HW Reset
miupll_266MHz
MIU0 zq=0x003b
miu_bw_set
utmi_1_init done
utmi_2_init done
utmi_3_init done
usbpll init done......
CPU=1200Mhz
cpupll init done
SPI 54M
clk_init done
P1 USB_rterm trim=0x000d
P1 USB_HS_TX_CURRENT trim=0x000d
P2 USB_rterm trim=0x000d
P2 USB_HS_TX_CURRENT trim=0x0001
P3 USB_rterm trim=0x000d
P3 USB_HS_TX_CURRENT trim=0x0001
PM_vol_bgap trim=0x0002
GCR_SAR_DATA trim=0x0190
ETH 10T output swing trim=0x0010
ETH 100T output swing trim=0x0010
ETH RX input impedance trim=0x0000
ETH TX output impedance trim=0x0000
MIPI_HS_RTERM trim=0x0001
MIPI_LP_RTERM trim=0x0000
TX_current trimming trim[0x1A]=0x0048
TX_current trimming trim[0x1B]=0x0048
TX_current trimming trim[0x1C]=0x0047
HDMI2TX Rterm trim=0x0000
HDMI2TX_Ibias_CH0 trim=0x001a
HDMI2TX_Ibias_CH1 trim=0x001a
HDMI2TX_Ibias_CH2 trim=0x0019
HDMI2TX_Ibias_CH3 trim=0x001b
256MB
BIST0_0001-OK
Enable MMU and CACHE
Load IPL_CUST from NOR
offset:000061c0
Flash:204018
XMC QE=1
Load time 843 us, 25888 KiB/s
Checksum OK

IPL_CUST ga5271e7
MXP found at 0x0000c000
runUBOOT()
runUBOOT()
[SPI_NOR]
Load time 15867 us, 13267 KiB/s
-Verify UBOOT CRC32 passed!
-Decompress UBOOT XZ
decomp_size=0x00091bf8
Disable MMU and D-cache before jump to UBOOT
К

U-Boot 2015.01-svn278045 (Oct 21 2024 - 17:24:02), Build: jenkins-Product_build_Customize_NVR_ALL_2-449

Version: I2g#######
[WDT] Enalbe WATCHDOG 60s
Watchdog enabled
I2C: ready
DRAM:
WARNING: Caches not enabled
MMC: MStar SD/MMC: 0
nor_flash_mxp allocated success!!
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
MXP found at mxp_offset[1]=0x0000C000, size=0x1000
env_offset=0x50000 env_size=0x1000
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
Board Type : NVR301-16S3-P8
Hw Type : 0x1
PCB Version : A
Front Type : A
Front PCB : A
In: serial
Out: serial
Err: serial
Net: MAC Address E4:F1:4C:82:92:E1
Auto-Negotiation...
AN failLink Status Speed:10 Full-duplex:0
Status Error!
sstar_emac
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
SF: 20480 bytes @ 0x51000 Read: OK
_BootLogoJpdCtrl 1324:: Create Decompress struct
_BootLogoJpdCtrl 1332:: Set memory buffer as source
_BootLogoJpdCtrl 1344:: Read the JPEG header
_BootLogoJpdCtrl 1357:: Initiate JPEG decompression
_BootLogoJpdCtrl 1371:: Image is 1280 by 720 with 3 components
_BootLogoJpdCtrl 1383:: BmpBuffer: 0x2398e3f0
_BootLogoJpdCtrl 1396:: Start reading scanlines
_BootLogoJpdCtrl 1406:: Done reading scanlines
_BootLogoJpdCtrl 1411:: End of decompression
_BootLogoYuv444ToYuv420 1276:: 444 To 422, In:2398e3f0, Out:27700000, Width:1280, Height:720
_BootLogoHdmitxCtrl 1600
(Re)start USB 1...
Check USB port[1]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2018.01.12
[USB] Port 1 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1f284a00
[USB] UHC Base 1f285000
[USB] USBC Base 1f284e00
[USB] BC Base 1f284c00
[USB] config miu select [70] [f8] [ef] ][ef]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
do_usb_start port:1 execute error
(Re)start USB 2...
Check USB port[2]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2018.01.12
[USB] Port 2 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1f285200
[USB] UHC Base 1f286400
[USB] USBC Base 1f286200
[USB] BC Base 1f286000
[USB] config miu select [70] [f8] [ef] ][ef]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
do_usb_start port:2 execute error
Usb start command error..
** Bad device usb 0 **
cmd(fatload usb 0 0x20500000 /equv1.bin) execute error
** Bad device usb 0 **
cmd(fatload usb 0 0x20500000 /recover/Program.bin) execute error
[NetUpgrade] ts_1st=0x2705
[NetUpgrade] Get Device MacAddr(E4:F1:4C:82:92:E1)
NetUpgrade Timeout
[NetUpgrade] ts_1st=0x2705, ts_2nd=0x2af1, delt_ts=0x3ec
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
SF: 1900544 bytes @ 0xc0000 Read: OK
## Booting kernel from Legacy Image at 20500000 ...
Image Name: MVX4##I2M#g#######KL_LX409##[BR:
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 1896108 Bytes = 1.8 MiB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Uncompressing Kernel Image ...
[XZ] !!!reserved 0x21000000 length=0x 1000000 for xz!!
XZ: uncompressed size=0x4dc000, ret=7
OK
Info: Bootargs console=ttyS0,115200n8 root=/dev/mtdblock5 rootfstype=squashfs LX_MEM=0xFF00000 mma_heap=MMU_MMA,miu=0,sz=0x3A00000 mma_heap=mma_heap_name0,miu=0,sz=0x03100000 mma_memblock_remove=1 boot_info.mode=normal boot_info.brand=02
atags:0x20000000

Starting kernel ...

[ 0.000000] early_atags_to_fdt() success
[ 0.000000] [vsboard] Looking for gstSysPubInfo properties...
[ 0.000000] [vsboard]setup kernel public sys info ok for NVR301-16S3-P8
[ 0.000000] Func DRV_BOARD_Init Line 1118: DRV_BOARD_Init : DevType=0x360e011c

[ 0.000000] [VSBOARD]setup kernel private sys info ok for NVR301-16S3-P8
[ 0.000000] LXmem is 0xff00000 PHYS_OFFSET is 0x20000000
[ 0.000000]
[ 0.000000] LX_MEM = 0x20000000, 0xff00000
[ 0.000000] LX_MEM2 = 0x0, 0x0
[ 0.000000] LX_MEM3 = 0x0, 0x0
[ 0.000000] EMAC_LEN= 0x0
[ 0.000000] DRAM_LEN= 0x0
[ 0.000000] deal_with_reserve_mma_heap memblock_reserve success mma_config[0].reserved_start=
[ 0.000000] 0x20600000
[ 0.000000]
[ 0.000000] deal_with_reserve_mma_heap memblock_reserve success mma_config[1].reserved_start=
[ 0.000000] 0x2b900000
[ 0.000000]
[ 0.000000] ms_init_main_intc: np->name=ms_main_intc, parent=gic
[ 0.000000] ms_init_pm_intc: np->name=ms_pm_intc, parent=ms_main_intc
[ 0.000000] ss_init_gpi_intc: np->name=ms_gpi_intc, parent=ms_main_intc
[ 0.000000] Find CLK_cpupll_clk, hook ms_cpuclk_ops
[ 0.128480] [ss_gpi_intc_domain_alloc] hw:42 -> v:50
[ 0.134735] [MS_PM_INTC] hw:20 -> v:58
[ 0.139874] [vsboard] i2c device is register to kernel completed!
[ 0.145934] [vsboard] i2c device init success.
[ 0.186748] Initialize watchdog successful
[ 0.212212] Mstar_ehc_init version:20180309
[ 0.216349] Sstar-ehci-2 H.W init
[ 0.219543] CHIP_FUNCTION SET. ID=4, param=65537
[ 0.224180] Titania3_series_start_ehc start
[ 0.228333] [USB] config miu select [70] [e8] [ef] [ef]
[ 0.233553] [USB] enable miu lower bound address subtraction
[ 0.239222] [USB] init squelch level 0x2
[ 0.244162] BC disable
[ 0.275012] Sstar-ehci-1 H.W init
[ 0.278166] CHIP_FUNCTION SET. ID=4, param=1
[ 0.282437] Titania3_series_start_ehc start
[ 0.286761] [USB] config miu select [70] [e8] [ef] [ef]
[ 0.291829] [USB] enable miu lower bound address subtraction
[ 0.297501] [USB] init squelch level 0x2
[ 0.302437] BC disable
[ 0.335017] Sstar-ehci-3 H.W init
[ 0.338171] CHIP_FUNCTION SET. ID=4, param=131073
[ 0.342882] Titania3_series_start_ehc start
[ 0.347080] [USB] config miu select [70] [e8] [ef] [ef]
[ 0.352268] [USB] enable miu lower bound address subtraction
[ 0.357937] [USB] init squelch level 0x2
[ 0.362874] BC disable
[ 0.396819] MSYS: DMEM request: [emac0_buff]:0x00000812
[ 0.401936] MSYS: DMEM request: [emac0_buff]:0x00000812 success, CPU phy:@0x2B64D000, virt:@0xCB64D000
[ 0.411649] mdio_bus mdio-bus@emac0: /soc/emac0/mdio-bus@emac0/ethernet-phy@0 has invalid PHY address
[ 0.421319] [emac_phy_connect][3262] connected mac emac0 to PHY at mdio-bus@emac0:00 [uid=11112222, driver=SStar 10/100 Ethernet Phy]
[ 0.433899] MSYS: DMEM request: [emac1_buff]:0x00060812
[ 0.439227] MSYS: DMEM request: [emac1_buff]:0x00060812 success, CPU phy:@0x2B650000, virt:@0xCB650000
[ 0.449059] [emac_phy_connect][3262] connected mac emac1 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 0.461421] MSYS: DMEM request: [BDMA_FSP_WBUFF]:0x00010040
[ 0.466996] MSYS: DMEM request: [BDMA_FSP_WBUFF]:0x00010040 success, CPU phy:@0x2B6C0000, virt:@0xCB6C0000
[ 0.476517] [Ser flash] phys=0x2b6c0000, virt=0xcb6c0000, bus=0x0b6c0000 len:0x10040
[ 0.484265] [FSP] Unknown flash type (0xFF, 0xFF, 0xFF) and use default flash type 0x0000
[ 0.492425] [FSP] 1-1-4 QUAD_READ MODE
[ 0.496855] MXP found at mxp_offset[1]=0x0000C000, size=0x1000
[ 0.509507] cpufreq: cpufreq_online: Failed to initialize policy for cpu: 0 (-61)
[ 0.518491] the 6 i2c_desc is not assign the name or addr
[ 0.523730] the 7 i2c_desc is not assign the name or addr
[ 0.529159] the 8 i2c_desc is not assign the name or addr
[ 0.534537] the 9 i2c_desc is not assign the name or addr
[ 0.539919] i2c device is really inited ok
[ 0.582055] squashfs: SQUASHFS error: unable to read id index table
[ 0.588488] List of all partitions:
[ 0.591819] 1f00 16384 mtdblock0 [ 0.595831] (driver?)
[ 0.598169] 1f01 320 mtdblock1 [ 0.602169] (driver?)
[ 0.604529] 1f02 64 mtdblock2 [ 0.608523] (driver?)
[ 0.610876] 1f03 384 mtdblock3 [ 0.614885] (driver?)
[ 0.617230] 1f04 1856 mtdblock4 [ 0.621230] (driver?)
[ 0.623583] 1f05 13440 mtdblock5 [ 0.627589] (driver?)
[ 0.629937] 1f06 64 mtdblock6 [ 0.633937] (driver?)
[ 0.636297] 1f07 64 mtdblock7 [ 0.640291] (driver?)
[ 0.642644] 1f08 128 mtdblock8 [ 0.646651] (driver?)
[ 0.648999] 1f09 64 mtdblock9 [ 0.652998] (driver?)
[ 0.655359] No filesystem could mount root, tried: [ 0.660049] squashfs
[ 0.662311]
[ 0.663795] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
[ 0.672151] CPU1: stopping
[ 0.674850] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.9.84 #1
[ 0.680764] Hardware name: SStar Soc (Flattened Device Tree msr621d)
[ 0.687139] [<c0014604>] (unwind_backtrace) from [<c0011b84>] (show_stack+0x10/0x14)
[ 0.694873] [<c0011b84>] (show_stack) from [<c017cdb0>] (dump_stack+0x7c/0x9c)
[ 0.702095] [<c017cdb0>] (dump_stack) from [<c00137e4>] (handle_IPI+0xcc/0x184)
[ 0.709405] [<c00137e4>] (handle_IPI) from [<c00093b0>] (gic_handle_irq+0x78/0x80)
[ 0.716976] [<c00093b0>] (gic_handle_irq) from [<c0012638>] (__irq_svc+0x58/0x74)
[ 0.724457] Exception stack(0xcb283f98 to 0xcb283fe0)
[ 0.729506] 3f80: 00000000 000004a6
[ 0.737691] 3fa0: cb8ce27c c0019220 cb282000 c049a3e4 00000002 c04e28d1 c049a434 410fc075
[ 0.745872] 3fc0: 00000000 00000000 cb283f88 cb283fe8 c000f814 c000f818 60000013 ffffffff
[ 0.754055] [<c0012638>] (__irq_svc) from [<c000f818>] (arch_cpu_idle+0x2c/0x38)
[ 0.761455] [<c000f818>] (arch_cpu_idle) from [<c004fba0>] (cpu_startup_entry+0xc0/0x120)
[ 0.769635] [<c004fba0>] (cpu_startup_entry) from [<2000944c>] (0x2000944c)
[ 0.776596] Rebooting in 1 seconds..
1
IPL ga5271e7
D-1b
HW Reset
miupll_266MHz
MIU0 zq=0x003b
miu_bw_set
utmi_1_init done
utmi_2_init done
utmi_3_init done
usbpll init done......
CPU=1200Mhz
cpupll init done
SPI 54M
clk_init done
P1 USB_rterm trim=0x000d
P1 USB_HS_TX_CURRENT trim=0x000d
P2 USB_rterm trim=0x000d
P2 USB_HS_TX_CURRENT trim=0x0001
P3 USB_rterm trim=0x000d
P3 USB_HS_TX_CURRENT trim=0x0001
PM_vol_bgap trim=0x0002
GCR_SAR_DATA trim=0x0190
ETH 10T output swing trim=0x0010
ETH 100T output swing trim=0x0010
ETH RX input impedance trim=0x0000
ETH TX output impedance trim=0x0000
MIPI_HS_RTERM trim=0x0001
MIPI_LP_RTERM trim=0x0000
TX_current trimming trim[0x1A]=0x0048
TX_current trimming trim[0x1B]=0x0048
TX_current trimming trim[0x1C]=0x0047
HDMI2TX Rterm trim=0x0000
HDMI2TX_Ibias_CH0 trim=0x001a
HDMI2TX_Ibias_CH1 trim=0x001a
HDMI2TX_Ibias_CH2 trim=0x0019
HDMI2TX_Ibias_CH3 trim=0x001b
256MB
BIST0_0001-OK
Enable MMU and CACHE
Load IPL_CUST from NOR
offset:000061c0
Flash:204018
XMC QE=1
Load time 843 us, 25888 KiB/s
Checksum OK

IPL_CUST ga5271e7
MXP found at 0x0000c000
runUBOOT()
runUBOOT()
[SPI_NOR]
Load time 15867 us, 13267 KiB/s
-Verify UBOOT CRC32 passed!
-Decompress UBOOT XZ
decomp_size=0x00091bf8
Disable MMU and D-cache before jump to UBOOT
К

U-Boot 2015.01-svn278045 (Oct 21 2024 - 17:24:02), Build: jenkins-Product_build_Customize_NVR_ALL_2-449

Version: I2g#######
[WDT] Enalbe WATCHDOG 60s
Watchdog enabled
I2C: ready
DRAM:
WARNING: Caches not enabled
MMC: MStar SD/MMC: 0
nor_flash_mxp allocated success!!
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
MXP found at mxp_offset[1]=0x0000C000, size=0x1000
env_offset=0x50000 env_size=0x1000
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
Board Type : NVR301-16S3-P8
Hw Type : 0x1
PCB Version : A
Front Type : A
Front PCB : A
In: serial
Out: serial
Err: serial
Net: MAC Address E4:F1:4C:82:92:E1
Auto-Negotiation...
AN failLink Status Speed:10 Full-duplex:0
Status Error!
sstar_emac
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
SF: 20480 bytes @ 0x51000 Read: OK
_BootLogoJpdCtrl 1324:: Create Decompress struct
_BootLogoJpdCtrl 1332:: Set memory buffer as source
_BootLogoJpdCtrl 1344:: Read the JPEG header
_BootLogoJpdCtrl 1357:: Initiate JPEG decompression
_BootLogoJpdCtrl 1371:: Image is 1280 by 720 with 3 components
_BootLogoJpdCtrl 1383:: BmpBuffer: 0x2398e3f0
_BootLogoJpdCtrl 1396:: Start reading scanlines
_BootLogoJpdCtrl 1406:: Done reading scanlines
_BootLogoJpdCtrl 1411:: End of decompression
_BootLogoYuv444ToYuv420 1276:: 444 To 422, In:2398e3f0, Out:27700000, Width:1280, Height:720
_BootLogoHdmitxCtrl 1600
(Re)start USB 1...
Check USB port[1]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2018.01.12
[USB] Port 1 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1f284a00
[USB] UHC Base 1f285000
[USB] USBC Base 1f284e00
[USB] BC Base 1f284c00
[USB] config miu select [70] [f8] [ef] ][ef]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
do_usb_start port:1 execute error
(Re)start USB 2...
Check USB port[2]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2018.01.12
[USB] Port 2 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base 1f285200
[USB] UHC Base 1f286400
[USB] USBC Base 1f286200
[USB] BC Base 1f286000
[USB] config miu select [70] [f8] [ef] ][ef]
[USB] enable miu lower bound address subtraction
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] No USB is connecting
[USB] USB init failed
[USB] usb_lowlevel_init--
Error, couldn't init Lowlevel part
do_usb_start port:2 execute error
Usb start command error..
** Bad device usb 0 **
cmd(fatload usb 0 0x20500000 /equv1.bin) execute error
** Bad device usb 0 **
cmd(fatload usb 0 0x20500000 /recover/Program.bin) execute error
[NetUpgrade] ts_1st=0x2705
[NetUpgrade] Get Device MacAddr(E4:F1:4C:82:92:E1)
NetUpgrade Timeout
[NetUpgrade] ts_1st=0x2705, ts_2nd=0x2af1, delt_ts=0x3ec
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
SF: 1900544 bytes @ 0xc0000 Read: OK
## Booting kernel from Legacy Image at 20500000 ...
Image Name: MVX4##I2M#g#######KL_LX409##[BR:
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 1896108 Bytes = 1.8 MiB
Load Address: 20008000
Entry Point: 20008000
Verifying Checksum ... OK
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
-usb_stop(USB_PORT2)
Uncompressing Kernel Image ...
[XZ] !!!reserved 0x21000000 length=0x 1000000 for xz!!
XZ: uncompressed size=0x4dc000, ret=7
OK
Info: Bootargs console=ttyS0,115200n8 root=/dev/mtdblock5 rootfstype=squashfs LX_MEM=0xFF00000 mma_heap=MMU_MMA,miu=0,sz=0x3A00000 mma_heap=mma_heap_name0,miu=0,sz=0x03100000 mma_memblock_remove=1 boot_info.mode=normal boot_info.brand=02
atags:0x20000000

Starting kernel ...

[ 0.000000] early_atags_to_fdt() success
[ 0.000000] [vsboard] Looking for gstSysPubInfo properties...
[ 0.000000] [vsboard]setup kernel public sys info ok for NVR301-16S3-P8
[ 0.000000] Func DRV_BOARD_Init Line 1118: DRV_BOARD_Init : DevType=0x360e011c

[ 0.000000] [VSBOARD]setup kernel private sys info ok for NVR301-16S3-P8
[ 0.000000] LXmem is 0xff00000 PHYS_OFFSET is 0x20000000
[ 0.000000]
[ 0.000000] LX_MEM = 0x20000000, 0xff00000
[ 0.000000] LX_MEM2 = 0x0, 0x0
[ 0.000000] LX_MEM3 = 0x0, 0x0
[ 0.000000] EMAC_LEN= 0x0
[ 0.000000] DRAM_LEN= 0x0
[ 0.000000] deal_with_reserve_mma_heap memblock_reserve success mma_config[0].reserved_start=
[ 0.000000] 0x20600000
[ 0.000000]
[ 0.000000] deal_with_reserve_mma_heap memblock_reserve success mma_config[1].reserved_start=
[ 0.000000] 0x2b900000
[ 0.000000]
[ 0.000000] ms_init_main_intc: np->name=ms_main_intc, parent=gic
[ 0.000000] ms_init_pm_intc: np->name=ms_pm_intc, parent=ms_main_intc
[ 0.000000] ss_init_gpi_intc: np->name=ms_gpi_intc, parent=ms_main_intc
[ 0.000000] Find CLK_cpupll_clk, hook ms_cpuclk_ops
[ 0.128496] [ss_gpi_intc_domain_alloc] hw:42 -> v:50
[ 0.134751] [MS_PM_INTC] hw:20 -> v:58
[ 0.139890] [vsboard] i2c device is register to kernel completed!
[ 0.145953] [vsboard] i2c device init success.
[ 0.186746] Initialize watchdog successful
[ 0.212083] Mstar_ehc_init version:20180309
[ 0.216220] Sstar-ehci-2 H.W init
[ 0.219415] CHIP_FUNCTION SET. ID=4, param=65537
[ 0.224053] Titania3_series_start_ehc start
[ 0.228204] [USB] config miu select [70] [e8] [ef] [ef]
[ 0.233425] [USB] enable miu lower bound address subtraction
[ 0.239094] [USB] init squelch level 0x2
[ 0.244043] BC disable
[ 0.275013] Sstar-ehci-1 H.W init
[ 0.278167] CHIP_FUNCTION SET. ID=4, param=1
[ 0.282439] Titania3_series_start_ehc start
[ 0.286719] [USB] config miu select [70] [e8] [ef] [ef]
[ 0.291829] [USB] enable miu lower bound address subtraction
[ 0.297500] [USB] init squelch level 0x2
[ 0.302437] BC disable
[ 0.334984] Sstar-ehci-3 H.W init
[ 0.338138] CHIP_FUNCTION SET. ID=4, param=131073
[ 0.342850] Titania3_series_start_ehc start
[ 0.347056] [USB] config miu select [70] [e8] [ef] [ef]
[ 0.352236] [USB] enable miu lower bound address subtraction
[ 0.357905] [USB] init squelch level 0x2
[ 0.362844] BC disable
[ 0.396807] MSYS: DMEM request: [emac0_buff]:0x00000812
[ 0.401926] MSYS: DMEM request: [emac0_buff]:0x00000812 success, CPU phy:@0x2B64D000, virt:@0xCB64D000
[ 0.411651] mdio_bus mdio-bus@emac0: /soc/emac0/mdio-bus@emac0/ethernet-phy@0 has invalid PHY address
[ 0.421306] [emac_phy_connect][3262] connected mac emac0 to PHY at mdio-bus@emac0:00 [uid=11112222, driver=SStar 10/100 Ethernet Phy]
[ 0.433880] MSYS: DMEM request: [emac1_buff]:0x00060812
[ 0.439208] MSYS: DMEM request: [emac1_buff]:0x00060812 success, CPU phy:@0x2B650000, virt:@0xCB650000
[ 0.449046] [emac_phy_connect][3262] connected mac emac1 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[ 0.461400] MSYS: DMEM request: [BDMA_FSP_WBUFF]:0x00010040
[ 0.466975] MSYS: DMEM request: [BDMA_FSP_WBUFF]:0x00010040 success, CPU phy:@0x2B6C0000, virt:@0xCB6C0000
[ 0.476494] [Ser flash] phys=0x2b6c0000, virt=0xcb6c0000, bus=0x0b6c0000 len:0x10040
[ 0.484243] [FSP] Unknown flash type (0xFF, 0xFF, 0xFF) and use default flash type 0x0000
[ 0.492403] [FSP] 1-1-4 QUAD_READ MODE
[ 0.496839] MXP found at mxp_offset[1]=0x0000C000, size=0x1000
[ 0.509549] cpufreq: cpufreq_online: Failed to initialize policy for cpu: 0 (-61)
[ 0.518542] the 6 i2c_desc is not assign the name or addr
[ 0.523780] the 7 i2c_desc is not assign the name or addr
[ 0.529203] the 8 i2c_desc is not assign the name or addr
[ 0.534588] the 9 i2c_desc is not assign the name or addr
[ 0.539969] i2c device is really inited ok
[ 0.581893] squashfs: SQUASHFS error: unable to read id index table
[ 0.588328] List of all partitions:
[ 0.591660] 1f00 16384 mtdblock0 [ 0.595668] (driver?)
[ 0.598009] 1f01 320 mtdblock1 [ 0.602009] (driver?)
[ 0.604369] 1f02 64 mtdblock2 [ 0.608362] (driver?)
[ 0.610716] 1f03 384 mtdblock3 [ 0.614725] (driver?)
[ 0.617070] 1f04 1856 mtdblock4 [ 0.621070] (driver?)
[ 0.623423] 1f05 13440 mtdblock5 [ 0.627429] (driver?)
[ 0.629777] 1f06 64 mtdblock6 [ 0.633777] (driver?)
[ 0.636137] 1f07 64 mtdblock7 [ 0.640131] (driver?)
[ 0.642484] 1f08 128 mtdblock8 [ 0.646490] (driver?)
[ 0.648838] 1f09 64 mtdblock9 [ 0.652838] (driver?)
[ 0.655199] No filesystem could mount root, tried: [ 0.659888] squashfs
[ 0.662151]
[ 0.663635] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
[ 0.671991] CPU1: stopping
[ 0.674689] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.9.84 #1
[ 0.680604] Hardware name: SStar Soc (Flattened Device Tree msr621d)
[ 0.686979] [<c0014604>] (unwind_backtrace) from [<c0011b84>] (show_stack+0x10/0x14)
[ 0.694713] [<c0011b84>] (show_stack) from [<c017cdb0>] (dump_stack+0x7c/0x9c)
[ 0.701934] [<c017cdb0>] (dump_stack) from [<c00137e4>] (handle_IPI+0xcc/0x184)
[ 0.709245] [<c00137e4>] (handle_IPI) from [<c00093b0>] (gic_handle_irq+0x78/0x80)
[ 0.716816] [<c00093b0>] (gic_handle_irq) from [<c0012638>] (__irq_svc+0x58/0x74)
[ 0.724297] Exception stack(0xcb283f98 to 0xcb283fe0)
[ 0.729346] 3f80: 00000000 000004f6
[ 0.737531] 3fa0: cb8ce27c c0019220 cb282000 c049a3e4 00000002 c04e28d1 c049a434 410fc075
[ 0.745712] 3fc0: 00000000 00000000 00000000 cb283fe8 c000f814 c000f818 60000013 ffffffff
[ 0.753895] [<c0012638>] (__irq_svc) from [<c000f818>] (arch_cpu_idle+0x2c/0x38)
[ 0.761295] [<c000f818>] (arch_cpu_idle) from [<c004fba0>] (cpu_startup_entry+0xc0/0x120)
[ 0.769474] [<c004fba0>] (cpu_startup_entry) from [<2000944c>] (0x2000944c)
[ 0.776436] Rebooting in 1 seconds..
1
IPL ga5271e7
D-1b
HW Reset
miupll_266MHz
MIU0 zq=0x003b
miu_bw_set
utmi_1_init done
utmi_2_init done
utmi_3_init done
usbpll init done......
CPU=1200Mhz
cpupll init done
SPI 54M
clk_init done
P1 USB_rterm trim=0x000d
P1 USB_HS_TX_CURRENT trim=0x000d
P2 USB_rterm trim=0x000d
P2 USB_HS_TX_CURRENT trim=0x0001
P3 USB_rterm trim=0x000d
P3 USB_HS_TX_CURRENT trim=0x0001
PM_vol_bgap trim=0x0002
GCR_SAR_DATA trim=0x0190
ETH 10T output swing trim=0x0010
ETH 100T output swing trim=0x0010
ETH RX input impedance trim=0x0000
ETH TX output impedance trim=0x0000
MIPI_HS_RTERM trim=0x0001
MIPI_LP_RTERM trim=0x0000
TX_current trimming trim[0x1A]=0x0048
TX_current trimming trim[0x1B]=0x0048
TX_current trimming trim[0x1C]=0x0047
HDMI2TX Rterm trim=0x0000
HDMI2TX_Ibias_CH0 trim=0x001a
HDMI2TX_Ibias_CH1 trim=0x001a
HDMI2TX_Ibias_CH2 trim=0x0019
HDMI2TX_Ibias_CH3 trim=0x001b
256MB
BIST0_0001-OK
Enable MMU and CACHE
Load IPL_CUST from NOR
offset:000061c0
Flash:204018
XMC QE=1
Load time 843 us, 25888 KiB/s
Checksum OK

IPL_CUST ga5271e7
MXP found at 0x0000c000
runUBOOT()
runUBOOT()
[SPI_NOR]
Load time 15867 us, 13267 KiB/s
-Verify UBOOT CRC32 passed!
-Decompress UBOOT XZ
decomp_size=0x00091bf8
Disable MMU and D-cache before jump to UBOOT
К

U-Boot 2015.01-svn278045 (Oct 21 2024 - 17:24:02), Build: jenkins-Product_build_Customize_NVR_ALL_2-449

Version: I2g#######
[WDT] Enalbe WATCHDOG 60s
Watchdog enabled
I2C: ready
DRAM:
WARNING: Caches not enabled
MMC: MStar SD/MMC: 0
nor_flash_mxp allocated success!!
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
MXP found at mxp_offset[1]=0x0000C000, size=0x1000
env_offset=0x50000 env_size=0x1000
Flash is detected (0x0C0A, 0x20, 0x40, 0x18)
SF: Detected nor0 with total size 16 MiB
Board Type : NVR301-16S3-P8
Hw Type : 0x1
PCB Version : A
Front Type : A
Front PCB : A
In: serial
Out: serial
Err: serial
Net: MAC Address E4:F1:4C:82:92:E1
Auto-Negotiation...
<0>