Автор темы
Участники
|
Мои познания в ремонте данного вида техники: Занимаюсь ремонтом
Наличие схемы: нет
Магнитола LAN5000EKQL ARUSK2 96560-F1030WK (KIA SPORTAGE 4). При включяение черный экран и уходит в перезагрузку через секунд 5. Флешку проверил, прошивка есть и живая. Лог вот такой. Рубиться на вот этих строчках
ERROR : UART4MonitorThread() : TimeOut : nLoop = 1, GetTickCount() = 10796
nLoop = 1, g_nRxIntrCount = 1
Может кто знает в чем дело. Железо или софт?
INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
Microsoft Windows CE Bootloader Common Library Version 1.4 Built Jan 22 2016 18:13:22
Set PMU_REG_CORE 582c16
INFO: BoardID = 0xffff.
Microsoft Windows CE Ethernet Bootloader 1.0 for MX6Q SABREAuto (Jan 22 2016 18:19:00)
INFO: SBMR = 0x4060.
INFO: Bootloader launched from SD/eMMC.
USDHC[1] is being activated...
SDCardPowerSetUp
SD Card detected
MMC High Density card
MMC: boot info: 0x07
WR_REL_PARAM (166) = 0x5, WR_REL_SET (167) = 0x1f
*pdwRate = 52000000, ulDiv = 3, ulPrescaler = 1
MMC: Switch to bus width to ddr 8-bit mode.
MMC: No Boot Partition is enabled
INFO: Loading boot configuration from SDHC
INFO: Successfully loaded boot configuration from SDHC
ByOTP : GP1 = 0x0, bHeader = 0x0, bCarType = 0, bCarOption = 0
ByOTP : ReadCarType = 0x0, CarType_HMC_KIA = 0, TouchType_Max_Mxt = 0, LCDType_7Inch_8Inch = 0
ByOTP : 0x0, 0x0, 0x0, 0x0, 0, 0
ReadCarType = 0x55aa, CarType_HMC_KIA = 2, TouchType_Max_Mxt = 2, LCDType_7Inch_8Inch = 1
0x49, 0x56, 0x49, 1, 12, 18
DisplayIOMUXSetup() : LCDType_7Inch_8Inch = 1.
System ready!
Preparing for download...
kerenl boot fail set sueccess..(Boot Loader mode)
INFO: BT Enable High..
-BLMenu .
INFO: Using device name: 'MX6Q65535'
Valid Signature
NKCurPart=1, read = 1
INFO: Reading NK image to SDHC (please wait)...
INFO: Copying NK image to RAM address 0xa0300000
INFO: Read is 100% complete
INFO: Copy of NK Next completed successfully(select =1)
Download successful! Jumping to image at 0x0 (physical 0x1▒▒▒=▒OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
Windows CE Kernel for ARM (Thumb Enabled)
PL310 ID = 0x410000c7
L2 cache enabled
OEMInit: silicon rev = 0x15
BoardID = 0xffff.
SMP support enabled
-OEMInit
+OEMMpStartAllCPUs
Detected 2 CPUs
-OEMMpStartAllCPUs
OEMMpPerCPUInit: CPU1 is running
OALIoCtlHalInitRTC(2000/1/1 0:0:0.000)
DDK_IOMUX_PAD_NANDF_CS0 = 0x1b0b0
DDK_IOMUX_PAD_NANDF_CS0 = 0x1b088
DDK_IOMUX_PAD_NANDF_CS1 = 0x1b0b0
DDK_IOMUX_PAD_NANDF_CS1 = 0x1b088
ERROR: GetExtRealTime: RX8803 Power loss!
WARNING: SNVS was reset.
CPU Num:2
Allocated new interlock ID:10
Allocated new interlock ID:11
DDK Init +++
DDK Init ---
BSPCSPISetIOMux : LG_LCN_IOMUX_PIN_CHG_EN_GPIO is high
Allocated new interlock ID:12
rxDMABufSize = 1024
DMARxPriority = 5
USBware::DllMain: Started hModule 0x9B425D9C, dwReason 1
USBware::DllMain: Attach called - Current Process: 0x00000042, ID: 0x00400002
USBware::DllMain: Started hModule 0x9B425D9C, dwReason 0
USBware::DllMain: Detach called - Current Process: 0x00000042, ID: 0x00400002
Priority = 99
[829l][tace_info]hydra driver dll attach...
[831l][tace_info]<HYD_Init> : init_thread_id<0x03630002>
[831l][tace_info]<hydra_drv_init_thCannot update Pd> : Start<831>
[[42l4_AUDIO] fo]<hyctive r_init_threa
> : EnterCriticalSection<842>
SDHC[1] is pol[849l]ard d_info]SdioFunctionDriverInit::_ufsdio_load=0xef111508, _ufsDevicnitielied Evt
118SDaC
ufsdio_loadd 58>
SDHC[1] Card presented 0x1[862l][tace_info]skeleton dll attach...
[866l][tace_info]SKE_Init:: Index 1, pSkeDrvInfo 0x9f4535a0
RECOVERY: key_name H HIGH
cEvent, event_name CSRC9300\RecoveryHydraPanic1, chip_number 1
RECOVERY: key_name BtActEvent, event_name CSRC9300\RecoveryBtAct1, chip_number 1
RECOVERY: key_name WifiActEvent, event_name CSRC9300\RecoveryWifiAct1, chip_number 1
RECOVERY: chip 1 handles are 0x2830007, 0x2840007, 0x2870007
BT EN LOW
BT EN HIGH
SDHC[1] Card presented 0x1
SlotVoltage(1), New SetVolt=262144, Old SetVolt=0
CUSDHCBase::SetClockRate(1) : ulDiv = 5, ulPrescaler = 1
CUSDHCBase::SetClockRate(1) : ulDiv = 5, ulPrescaler = 1
**UNKNOWN**
CardDetectThread : SDHC[1] USDHC_PRSSTAT_CDIHB
SDHC[3] is using DAT3 as card detect pin
SDHC[3] is polling card detection
DeviceInserted Evt
SDHC[3] Card presented 0x5
SDHC[3] Card presented 0x5
Cannot update PLL[PLL4_AUDIO] with active references!
read dwPinVal1 = 0
read SdDwCPaindDetectMessageThread : started...
SDHC[4] Card presented 0xd
SDHC[4] PWR ON
SDHC[4] CarSlotVoltagd 4), Nread dwolt=2l1 = 0
ld SetVolt=262144
DeviceInserted Evt
ReInit SD
ReadCarType = 0x55aa, CarType_HMC_KIA = 2, TouchType_Max_Mxt = 2, LCDType_7Inch_8Inch = 1
0x49, 0x56, 0x49, 0x1, 12, 18
BSPTouchHWSelect() : mXCard presenData(82
: CalibrationData_mXT : dwDataSize = 400,240 170,110 170,385 625,385 620,110
LG_LCN_IOMUX_PIN_CHG_EN_GPIO is 0
USBware::DllMain: Started hModule 0x9B4544DC, dwReason 1
USBware::DllMain: Attach called - Current Process: 0x00000042, ID: 0x00400002
USBware::UWD_Init: Starting pContext 0x9F465160
GPS is 1, GPS_ACTIVE_MODE
USBware version 4.1.53.May 28 2015 11:04:35
CPU Num:2
Allocated new interlock ID:10
kerenl boot fail set sueccess... (kernel mode)
USBPHY_TX = 0x10070700
SlotVoltage(3), New SetVolt=262144, Old SetVolt=262144
GALCORE 4.6.9(9754) (Nov 25 2014 22:55:51)
SlotVoltage(4), New SetVolt=262144, Old SetVolt=262144
Major GPU: SysIntr=37 MemBases=0x130000 MMU Version=0
2D GPU: SysIntr=38 MemBases=0x134000 MMU Version=0
VG GPU: SysIntr=39 MemBases=0x2204000
Video memory: BaseAddress=0x0 PhysBase=0x12278000 size=0x6000000 physSize=0x0
+ DDIPU::SetMode
DDIPU::SetMode: Got display mode, 0!
***e*ci_loc:lSetMode:version InitHard 1 ports
ReadCarType = 0x55aa, CarType_HMC_KIA = 2, TouchType_Max_Mxt = 2, LCDType_7Inch_8Inch = 1
0x49, 0x56, 0x49, 0x1, 12, 18
DisplayIOocal0: USB r dwLCon 2.07Inch_8Inchl0: ne
device, port=0 depth=0 speed=high
*****>DDIPU::SetMode: Calling DisplaySetGamma!
*****>DDIPU::SetMode: Calling SetupVideoMemory!
DisplayConfigureSingle+
DisplayConfigureSingle-
- DDIPU::SetMode
g_nMsg = 0xc000, Ret = WAIT_OBJECT_0
lcn_usb_event_handler() : g_bAPIInit = 1
ehci_local0: - Jungo Generic Root Hub, class 9/0, rev 2.00/af.00, addr 1
uhub0: 1 port with 1 removable, self powered
GetCardRegisters() : m_DeviceType = 2
ERROR: d:\wince700\platform\imx6q_sabreauto\CUSDHCBase::SetClockRate(4) : ulDiv = 5, ulPrescaler = 1
**UNKNOWN**
src\drivers\touch\integration\bsptouch_mxt540e.c line 397: mXT540E_ReadRegister: Read mXT540E register 0x0 failed, err code(-7)(-1622933504)!
Error : mXT540E_ReadInfoID
Touch Version : 0.0, 0.0
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
LCDType is 7inch, write T9_0_7Inch
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXSDHC[3] Card presented 0xd
SDHC[3] Card presented 0xd
T540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failedRegPath: de(-7)!
ctivOR: d:\211>
700\platGSC +imit ActiveautoPath: Drives\toutive\68 <32ion\bsptouchGSCt540it Active449: mXT54DriverteRegister9: 3rit>
GSC +Init Active RegPath: Drivers\Active\70 <3 226>
e mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x0 failed, err code(-7)!
Error : mXT540E_TouchHWConfig : T38_Version
ERROR: d:\wince700\platform\imx6q_sabreauto\src\drivers\touch\integration\bsptouch_mxt540e.c line 449: mXT540E_WriteRegister: Write mXT540E register 0x2c failed, err code(-7)!
Touch Config Write OK!!!
Exception 'Data Abort' (0x4): Thread-Id=042a0016(pth=9b477908), Proc-Id=00400002(pprc=822195e0) 'NK.EXE', VM-active=01f4000a(pprc=9b4113dc) 'udevice.exe'
PC=effa5474(k.coredll.dll+0x00055474) RA=ef1d36c8(touch.dll+0x000036c8) SP=aad1fd90, BVA=b2310000
IOCTL_TOUCH_GET_CARTYPE_HMC_KIA : *(DWORD *)pBufOut = 2
ReadCarType_HMC_KIA() : g_dwCarType_HMC_KIA = 2
+[SHELL - 3396] MyShell()
+[SHELL - 3398] After Check User Folder
+[SHELL] AddFont_CarType() : g_dwCarType_HMC_KIA = 2, g_MyShellStatus = 1
[SHELL] \TTS\FONT\CubeBa1.ttf Font loading success
[SHELL] \TTS\FONT\CubeR.ttf Font loading success
-[SHELL] AddFont_CarType()
MyShell() : MyShell_PostProcess()
[SHELL] **SPI LGE AVN EU 2.0 TT**
path = \Windows\Scratchy.exe
( Drivers\Active\67 )
( Drivers\Active\68 )
( Drivers\Active\69 )
( Drivers\Active\70 )
<SdNowInitialize> : status<0x00000000>, clk<24750000>, protect<0>, Interface<1>
<SdNowInitialize> : status<0x00000000>, ehs<0x02x>
<SdNowInitialize> : EHS enable, status<0x00000000 >
SdNowSetInterruptHandler(EF1119EC, A9A7D950)
[3896l][tace_info]<sdio_card_read_info_f0> : sd rev<0x03>
[3901l][tace_info]<sdio_card_read_info_f0> : shs<1>, ehs<2>
[3911l][tace_info]<sdio_card_configure_func> : F<0>
[3913l][tace_info]SdioFunctionDriverInit::manId=0x0, cardId=0x0, funcId=0x0, interface=0x0, blockSize=0x0, hydraDriverInfo=0xa9a7d950
[3925l][tace_info]<sdio_card_configure_func> : F<1>
[3930l][tace_info]SdioFunctionDriverInit::manId=0x32a, cardId=0x19, funcId=0x1, interface=0x0, blockSize=0x200, hydraDriverInfo=0xa9a7d950
[3942l][tace_info]<sdio_card_configure_func> : F<2>
[3947l][tace_info]SdioFunctionDriverInit::manId=0x32a, cardId=0x19, funcId=0x2, interface=0x2, blockSize=0x200, hydraDriverInfo=0xa9a7d950
[3960l][tace_info]<sdio_card_configure_func> : F<3>
[3964l][tace_info]SdioFunctionDriverInit::manId=0x32a, cardId=0x19, funcId=0x3, interface=0x0, blockSize=0x200, hydraDriverInfo=0xa9a7d950
[3977l][tace_info]<sdio_card_configure_func> : F<4>
[3982l][tace_info]SdioFunctionDriverInit::manId=0x32a, cardId=0x19, funcId=0x4, interface=0x0, blockSize=0x200, hydraDriverInfo=0xa9a7d950
ufsdio_set_clock_speed(300)
[3997l][tace_info]CsrSdioFunctionDriverInit:: ret = 0
[4002l][tace_info]CSR Hydra chip driver v40(null) (auto mode)
[4007l][tace_info]CSR Hydra chip driver built Jan 22 2016 17:41:35
[4013l][tace_info]hydra: kernelspace fileserver
[4018l][tace_info]hydra_file_server_module_setup
[4022l][tace_info]<os_thread_create> : thread<file_server_thread>, dwThreadId<0x04ba005a>
[4030l][tace_info]hsp: card deep sleep signalling is disabled (50 ms)
[4037l][tace_info]<os_thread_create> : thread<hydra-sdio-io>, dwThreadId<0x04ac005a>
[4044l][tace_info]<os_thread_create> : thread<hydra/complete>, dwThreadId<0x04cf005a>
[4052l][tace_info]hydra_sdio: SDIO clock limit 300000
[4056l][tace_info]CsrSdioMaxBusClockFrequencySet::maxFrequency=0x493e0
ufsdio_set_clock_speed(300)
[4066l][tace_info]CsrSdioFunctionEnable:: now SDIO_CCCR_IO_EN=0x2, bit=0x2
[4073l][tace_info]<os_thread_create> : thread<service_mgr_thread>, dwThreadId<0x04bc005a>
#hydra_sdace_info]efuse__hash 0x684a, chisrWif 0x4p, chinserted(249)hip_rev 0x2ed
hif: F4:ydra_file_pa
ch_ope][tace_inr=\windra_drvle to open i> : Lndows\subsal0_paioh0_fw0>
18A.hcf
hydra_file_patch_open::File to open is \windows\subsys0_patch0_fw0000018A.hcf, file size is 0x7a0, fFile=0x9f473a80
[4121l][tace_info]efuse_hash 0x684a, chip_ver 0x44, chip_var 0x2, chip_rev 0x2
RunProgram() normal - success : lpszImageName = \Windows\Scratchy.exe
+[SHELL - 4241] MyShell()
hydra_file_config_open::FileDir=\windows,File to open is \windows\subsys0_config2.hcf, file size is 0x80, fFileVerifyFontLoadThread(1) : g_MyShellSt=0x9f473a return.
[SCRATCHY]mountPart = 1 at [2000 - 1 - 1]
[SCRATCHY]sectorArea = 200 at [2000 - 1 - 1]
[SCRATCHY]autoOpt = 1, magicNumber = 0xdead2099
[SCRATCHY]Delay = 10, Result = 1, File=perf[4436][
tCompleteApp] [SCRAComplDelay = 1,Occured
Result = 1, File=TaskMgr_SMP.exe
[SCRATCHY]Delay = 2, Result = 1, File=touchc.exe
[SCRATCHY]compare file pass
Read Error / 1.0.5.0.0.2
hydra_file_config_open::FileDir=\windows,File to open is \windows\subsys0_config2.hcf, file size is 0x80, fFile=0x9f473a80
[4487l][tace_info]efuse_hash 0x684a, chip_ver 0x44, chip_var 0x2, chip_rev 0x2
hydra_file_patch_open::FileDir=\windows,File to open is \windows\subsys6_patch0_fw0000018A.hcf
hydra_file_patch_open::File to open is \windows\subsys6_patch0_fw0000018A.hcf, file size is 0x3e0, fFile=0x9f473a80
[4523l][tace_info]hydra: S1: added service with provider 0, class 0x0000
[4527l][tace_info]hydra: S2: added service with provider 3, class 0x0000
[4533l][tace_info]hydra: S3: added service with provider 3, class 0x0500
[4540l][tace_info]hydra: S4: added service with provider 2, class 0x0000
[4546l][tace_info]hydra: S5: added service with provider 2, class 0x0100
[4553l][tace_info]hydra: S6: added service with provider 2, class 0x0102
[4559l][tace_info]hydra: S7: added service with provider 4, class 0x0000
[4566l][tace_info]hydra: S8: added service with provider 4, class 0x0200
[4572l][tace_info]hydra: S9: added service with provider 4, class 0x0201
[4579l][tace_info]Subsystem = Curator : HW Ver = 8772 (0x2244): FW ROM Ver = 394 : FW patch Ver = 639 : ID_STRING = 2013-09-20 14:42 curator_amber_d02_auto 394 cursw@camunxgrd79@ 1725371
[4580l][tace_info]hydra: hsp sdio max clock request
[4600l][tace_info]hydra_sdio: SDIO clock limit 50000000
[4605l][tace_info]CsrSdioMaxBusClockFrequencySet::maxFrequency=0x2faf080
ufsdio_set_clock_speed(50000)
Partition name: Part00 /
Partition name: Part01 / MMCMemory
Partition name: Part02 / MMCMemory2
Partition name: Part03 / USER
Partition name: Part04 / TTS
Partition name: Part05 / UBACKUP
Partition name: Part06 / DATALOGS
**UNKNOWN**
**UNKNOWN**
**UNKNOWN**
**UNKNOWN**
**UNKNOWN**
Function Load Ok: SetDataPathA
Function Load Ok: HafAuthA
SOP Version detect
Read Device ID Info: 30A9DEA452F8
57 (9)
51 (3)
52 (4)
48 (0)
52 (4)
53 (5)
50 (2)
53 (5)
56 (8)
50 (2)
[SCRATCHY]HU Update State: 1 - 200
Search Main App : Success..!!
Launch Success : \MMCmemory\Storage card\system\Lisa.exe
[CmnLog] DLL_PROCESS_ATTACH : AttachCount 0 -> 1
[log file find start]
[log file find start] DATALOGS\LogMsg\data_spp1.txt
#################!!!!!!!!!!!!!!!!!!mCheckCnt : 1 !!!!!!!!!!!!
Exception 'Data Abort' (0x4): Thread-Id=054500aa(pth=9b48f270), Proc-Id=054600aa(pprc=9b4917c8) 'Lisa.exe', VM-active=054600aa(pprc=9b4917c8) 'Lisa.exe'
PC=000246e8(Lisa.exe+0x000146e8) RA=0009f7e8(Lisa.exe+0x0008f7e8) SP=0014fda0, BVA=004f51d1
ERROR : UART4MonitorThread() : TimeOut : nLoop = 1, GetTickCount() = 10796
nLoop = 1, g_nRxIntrCount = 1
INFO:OALLogSetZones: dpCurSettings.ulZoneMask: 0xb
Microsoft Windows CE Bootloader Common Library Version 1.4 Built Jan 22 2016 18:13:22
Set PMU_REG_CORE 582c16
INFO: BoardID = 0xffff.
Microsoft Windows CE Ethernet Bootloader 1.0 for MX6Q SABREAuto (Jan 22 2016 18:19:00)
INFO: SBMR = 0x4060.
INFO: Bootloader launched from SD/eMMC.
USDHC[1] is being activated...
SDCardPowerSetUp
SD Card detected
MMC High Density card
MMC: boot info: 0x07
WR_REL_PARAM (166) = 0x5, WR_REL_SET (167) = 0x1f
*pdwRate = 52000000, ulDiv = 3, ulPrescaler = 1
MMC: Switch to bus width to ddr 8-bit mode.
MMC: No Boot Partition is enabled
INFO: Loading boot configuration from SDHC
INFO: Successfully loaded boot configuration from SDHC
ByOTP : GP1 = 0x0, bHeader = 0x0, bCarType = 0, bCarOption = 0
ByOTP : ReadCarType = 0x0, CarType_HMC_KIA = 0, TouchType_Max_Mxt = 0, LCDType_7Inch_8Inch = 0
ByOTP : 0x0, 0x0, 0x0, 0x0, 0, 0
ReadCarType = 0x55aa, CarType_HMC_KIA = 2, TouchType_Max_Mxt = 2, LCDType_7Inch_8Inch = 1
0x49, 0x56, 0x49, 1, 12, 18
DisplayIOMUXSetup() : LCDType_7Inch_8Inch = 1.
System ready!
Preparing for download...
kerenl boot fail set sueccess..(Boot Loader mode)
INFO: BT Enable High..
-BLMenu .
INFO: Using device name: 'MX6Q65535'
Valid Signature
NKCurPart=1, read = 1
INFO: Reading NK image to SDHC (please wait)...
INFO: Copying NK image to RAM address 0xa0300000
INFO: Read is 90% complete
|
Файлы
Прошивки
Продажа
Литература
Статьи
Зарегистрировано всего