Приветствую! Нужна прошивка под прогер для Polar P50L32T2CSM майн TP.MS338E.PB803 панель V500DJ6-QE1. Пришел -висел на заставке. Вместо того, чтобы подцепить по ISP сразу выпаял eMMC и читать. Только .EXT_CSD и смог считать. eMMC мертвая. Заказал KLM4G1FEPD-B031, прошил на удачу вот этой прошивкой. Телик включается, и пультом и с кнопки, но вместо изо -тест RGB. Пробовал подкидывать прошивку USB, что прислала техподдержка, не хочет подхватывать. Помигает и все. Лог
DRAM_SIZE1=512 MB DRAM_SIZE2=512 MB DRAM_SIZE3= MB msIR_Initialize [SYS][Utopia]: [35mFunction = SYSOpen, Line = 815, current resource pri_shm content is: 0[m [SYS][Utopia]: [35mFunction = SYSOpen, Line = 834, [SYS INFO] OPEN INSTANCE...[m create instance at 296EAA38 with private size 108 bytes at 296EAA80 [MIU][Utopia]: [MIU INFO] miu opencreate instance at 296EAAF0 with private size 80 bytes at 296EAB38 create instance at 296EAB90 with private size 48 bytes at 296EABD8
uboot held at [294DDF60~2AC00000],size=017220A0 CPU : Messi Board: BD_MST091B_10ASXG_15281_MESSI DRAM: 172 MiB Now running in RAM - U-Boot at: 29D00000
eMMC: HS200 200MHz eMMC 3.63 GB [747FF8h] In: serial Out: serial Err: serial Net: No ethernet found. Get MAC from ethaddr env MAC: 0x70: 0x2E: 0xD9: 0x79:0x2E: 0x81 ####################################################################### ####################################################################### [AT][MBoot][Driver Init][619]
<env reload for CHECK_IF_MBOOT_DEFAULT_ENV> mmc change mount : system ** File not found /etc/set_env [0;31m[ERROR] loadscript:757: [0mNo enough buffer or path fail(/etc/set_env) : [src/MsUtility.c] [loadscript]
Changelist: 24543697 ============= set bootargs =============== Hit any key to stop autoboot: 0 AC on ====cvte power on check usb and upgrade ==== <628> do_cvte_init_at_prama4env Check USB port[0]: [USB] usb_lowlevel_init++ [USB] USB EHCI LIB VER: 2014.06.09 [USB] Port 0 is Enabled [USB] TV_usb_init (UTMI Init) ++ [USB] UTMI Base 1F207500 [USB] UHC Base 1F204800 [USB] USBC Base 1F200E00 [USB] BC Base 1F246C00 [USB] config miu select [30] [74] [FF] ][FF] [USB] TV_usb_init-- [USB] Usb_host_Init++ [USB] No USB is connecting [USB] USB init failed [USB] usb_lowlevel_init-- Error, couldn't init Lowlevel part Check USB port[1]: [USB] usb_lowlevel_init++ [USB] USB EHCI LIB VER: 2014.06.09 [USB] Port 1 is Enabled [USB] TV_usb_init (UTMI Init) ++ [USB] UTMI Base 1F207400 [USB] UHC Base 1F201A00 [USB] USBC Base 1F200F00 [USB] BC Base 1F246C40 [USB] config miu select [30] [74] [FF] ][FF] [USB] TV_usb_init-- [USB] Usb_host_Init++ [USB] No USB is connecting [USB] USB init failed [USB] usb_lowlevel_init-- Error, couldn't init Lowlevel part Check USB port[2]: [USB] usb_lowlevel_init++ [USB] USB EHCI LIB VER: 2014.06.09 [USB] Port 2 is Enabled [USB] TV_usb_init (UTMI Init) ++ [USB] UTMI Base 1F207200 [USB] UHC Base 1F227200 [USB] USBC Base 1F227000 [USB] BC Base 1F246C80 [USB] config miu select [30] [74] [FF] ][FF] [USB] TV_usb_init-- [USB] Usb_host_Init++ [USB] Async base addr: 0xAB8D080 [USB] Reg 0x28: 0xD080 0xAB8 [USB] disable run [USB] Host Speed:2 [USB] Host type:2 [USB] enable aynch [USB] Usb_host_Init-- [USB] usb_lowlevel_init-- scanning bus for devices... [USB] control1 max:40
[USB] interface[0] conf:1 value FF: 1 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found FAIL : can not init usb!!
Файлы
Прошивки
Продажа
Литература
Статьи
Для просмотра сообщения Вы должны быть Участником форума. Для этого Вам необходимо 
Зарегистрировано всего